Question about Computers & Internet

1 Answer

Garmin Streetpilot i3 GPS cannot load map to memory card

Try to load from cd that was load into computer and followed on screen instructions now connect the usb cable from GPS to computer and went to some steps and at one point on screen will saynot communicating with gps memory card. A message says if you continue to get this error, please check the following URL for additional information www.garmin.com/usbgpsfaq. PLease help me out so i can use my Garmin Streetpilot i3 gps. Thankyou, Kenneth/lome garmin nuvi 250w special edition HELP! down load upgrades will not load !!!!!!

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Garmin STREETPILOT C330

Posted on Nov 04, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i communicate from my pc to the ups on the 9 pin serial connection


Taken from the MGE UPS SYSTEMS, Network Management Card Installation manual (34003641EN/AD)


Run Hyper Terminal on a PC running Windows (9x, Me, NT4.0, 2000 or

higher).

Connect the card to the PC using the cable supplied.

Set up the terminal with the following communication parameters:

9600 bauds. 8 data bits.

1 stop bit. no parity.

no flow control.

ASCII: "echo typed characters locally" option disabled.

Press the Carriage return key. The configuration menu is displayed.

Enter the password (MGEUPS by default).

The main menu is displayed.

Select one of the items in the configuration menu.


Via the serial link or Telnet

Select the "Agent configuration" command by entering 1.

Select the item numbers and modify all the IP parameters (address, mask, gateway).

Once all the modifications have been made, exit following the instructions on the screen.


Restarting the card Via the serial link or Telnet

Select the "Restart agent" command by entering 6.

Then follow the instructions on the screen.


Restoring the default parameters Via Telnet or Hyper Terminal

Select the "Agent configuration" command by entering 1.

Select the "Reset configuration to default" command by entering 5.

Then follow the instructions on the screen

Nov 05, 2010 | MGE UPS Galaxy 3000 UPS System

2 Answers

Garmin gps


What operating system are you using? Windows Vista?

Jun 11, 2008 | Computers & Internet

2 Answers

Sound


no, you dont need to buy a new one... let somebody or technical to see to it if the sound card drivers is install inside or i think you have a CD Disk Utility for that Personal Computer you buy. Sound card won't run unless you install the sound card driver or program, hope it might help you... good luck!

Jul 09, 2009 | QVS NetStar (UPS650A) UPS System

1 Answer

Nldtr missing


Am I right in thinking you mean NTLDR and not NLDTR? If so here is the fix.

To fix the error on startup of NTLDR is missing in Win XP you should follow the steps below using a full version Win XP CD and the Recovery Console.
Insert the Windows CD and start the computer making sure the computer boots to the CD first.
When the Welcome to Setup screen appears, press R. (this may take a while to load)
Type a number corresponding to the Windows installation you wish to repair (usually 1) and press Enter. When prompted, type the administrator password and press Enter. (if no password was entered on you system then just press enter)
From the command prompt you want to copy NTLDR and NTDETECT.COM from the i386 folder of the CD to the root folder of the hard drive. This is much easier than it sounds and can be done by typing the commands below.
In the examples below C: is presumed to be your hard drive and D: is presumed to be your CD drive. You will need to change the drive letters to your own if you have more than one drive. ( if you are having problems entering \ then try pressing the # key to see if that works)
Type these 2 commands exactly and press enter after each one.
COPY D:\I386\NTLDR C:\
COPY D:\I386\NTDETECT.COM C:\
Now remove the Windows XP CD from the drive and restart the computer and your computer should now start normally.

http://ncane.com/vvb

Apr 22, 2009 | IBM Tripp Lite OfficePro 700 (10K1912) UPS...

1 Answer

Putting information from my computer onto a memory stick


Hello my name is Tim, First thing you are going to want to do is insert the memory stick and open it, if it doesnt automatically open try going to "my Computer" and locate it. then make sure there is sufficient memory on the memory stick. leave this window open and also oper the window with the pictures, you will need to drag each photo you want into the window that has your memory card, or you can select the whole photo folder by holding ctrl and pressing a. to select multiple photos to drag and drop but not all try holding ctrl while clicking on the photos you want then when you get them selected let go of ctrl and click and drag one of the highlighted photos to the memory stick, this also works with files. I hope I answered all your questions, Please leave feedback on me and let me know if you need anymore help. Thanks, Tim

Mar 13, 2009 | Compaq Computers & Internet

1 Answer

Computer does not recognize the cd rom drives on this computer


Hello my name is Tim, It sounds like you may need to reinstall the drivers and get your pc to locate the drives, you can usually get these drivers from the manfacturers website or from download.com for free, if you have the install disks for the dvd burner and cd rom you can use another pc to load them onto a usb drive and then transfer them to your pc that way. You can also go to controll panel, then device manager, and try to locate it there to see if it needs any drivers. I hope this heled you, please feel free to ask more questions and I will try to help.

Mar 12, 2009 | Computers & Internet

1 Answer

Beeping sound coming from samsung cpu; no image on screen.


Hi,

Depending on how many beeps, the sequence and the interval, this is indicative of a fault in either the video card or the memory. In some models this can also refer to the bios/motherboard fault.

If you PC came with an add-on video card, try to remove, clean the little gold tips and reinsert back. If the video is built-in to the motherboard, then it is sharing the memory. You can do the same with the memories. Remove, clean, reinsert. A good way of cleaning would be with the use of a pencil eraser rubbing on the gold strips/pins.

Hope that this be of some help/idea. Pls post back specific model of your PC as well as the sequence of beeps.

Good luck and kind regards.

Dec 31, 2007 | Computers & Internet

2 Answers

How can i format my computer


what do you want to format your hard drive so you can install a fresh windows install? if so you need to go into your bios and set the computer to boot from cd rom and then you can boot from your windows cd an format your computer from there

Dec 07, 2007 | Computers & Internet

1 Answer

Installation for canon pixma ip 1500


Hey you again, you rated me yesterday Inappropriate. Actually, fixya expert afraid to give some solution because you will rated us Inappropriate even the problem is came from you where you was not clearly stated your problem.

Ok, but anyway I am still to help you, Is it the problem goes to the manual installation you need or the driver instead?

Printers used to be the bugbear of computer users. They were difficult to set up and ornery in operation. That's no longer the case and it's likely you'll have no problems getting your printer up and running. This is particularly the case if your printer comes packaged with your computer system or if you stick to well-known brands such as Hewlett-Packard, Epson, Lexmark and Canon.
Connecting a printer involves four steps:
  1. Unpacking your printer, removing any packaging material and installing the ink or toner cartridge. Refer to your printer's instructions to guide you.
  2. Connecting the printer cable to the printer and to the back of your computer.
  3. Connecting the printer's power cord to a power outlet.
  4. Installing the printer driver and any additional software. The printer driver is a piece of software that tells your computer how to interact with your printer.
If your printer comes as part of your system, you may find that its driver is already installed. In that case, all you'll need to do is unpack it, connect the printer cable and power cord and switch on your computer.
geekgirl.tip: Get a cable One word of warning: Make sure you purchase a printer cable! Often, this is not included in your computer system, despite it being an essential item. You'll need the correct type of cable for your printer: If it's a USB-enabled printer, you need a USB cable (note, the new USB 2 cables work with older USB 1 printers, too; so if in doubt, get a USB 2 cable); if it's a parallel printer, you'll need a parallel cable.
Make sure you get a cable long enough to reach easily from your printer to your computer. However, you should avoid cables longer than 10', because long cables can cause problems with communication between printer and computer. Try to position your printer so a 6' (or shorter) cable can make the connection.
Follow the wizard If your printer's software has not been pre-installed, read any installation instructions that accompany your printer and follow those instructions. If no instructions are provided, follow this procedure:
(Note: This procedure applies to printers which use a parallel connection. If your printer uses a USB connection, you should connect it while Windows is running and it will be recognised.)
  1. Make sure you have your original Windows CD-ROM handy. You may need it.
  2. Switch the computer off.
  3. Connect the parallel printer cable to your computer.
  4. Connect the printer's power cord to a power outlet.
  5. Switch on the printer and the computer.
  6. In most cases, Windows will detect that you've attached a new hardware device and it will launch the Add Hardware Wizard and attempt to search for the appropriate software. If the wizard doesn't launch and Windows appears to ignore your printer, you can launch the Add Printer wizard yourself by clicking the Start button, selecting Control Panel, clicking Printers And Other Hardware, and then clicking Add Printer.
  7. If the printer is directly connected to your computer, select the Local Printer Attached To This Computer option. If you will be connecting to the printer via a network connection, select the Network Printer option, then click Next.
  8. The wizard will first try to search for any Plug and Play devices (these are components that should, by rights, automatically notify Windows when they're first connected). If the wizard discovers your printer, it will display further instructions to complete the installation. You may need to restart your system to finish.

Nov 23, 2007 | Computers & Internet

1 Answer

Can't load a software Essentials 2.0


Go to Start, My Computer, then you should see your software in that window, double click on it. If it's not there let me know, because you have other issues you'll need to deal with.

Nov 09, 2007 | Computers & Internet

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

kakima

Level 3 Expert

98694 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...