Stays on constantly

Remove the fuse for radio. The tape player should stop clicking. Then try to see if the battery dies.

The yellow maintains memory and display if it has a clock, So that might be what you are seeing.

Error oL means overload.
If the "oL" error code appears, the washer has been filled with a load that is too large for its capacity, causing it to drain.

*Remove some items from the washer and add more detergent since the previous amount will have drained with the water.
*Close the washer and press the START/PAUSE/Cancel button to remove error displayed and restart the cycle.

If Pause/Cancel does not work:

*Unplug washer or disconnect power for one minute.
*Plug in washer or reconnect power.
*Re-select the cycle and press Start.

NOTE: If the error remains on the display, and the condition above has been checked, call for service.

Hope this helps.. :)

Hello & Welcome to FixYa

F21 error is displayed when the washer is unable to drain, press PAUSE/CANCEL button twice to clear the display. After this please check the drain hose and drain pump filter for any blockages and make sure it is not clogged with foreign particles. You can also check the drain pump to verify that its working. Please get back to me if you have any other questions.

Kevin

HELLO.

What you need to do is to reformat your phone and his memory card .

Who you will reformat your phone and it memory card click on your phone menu screw down to setting click on it screw down to phone setting click on it screw down to format or reformat then click on it .

Then allow it to format it self
' then operate your phone again'

If the problem remain then you will have to reformat the phone memory card, as the explanation give above that is click on the menu screw down to setting click on it screw to phone setting click on it screw to memory card click on it then click on format or reformat allow it to format it self .

After all this the problem remain same then applied this formula *2767*2878# and send it sure it will be ok

Good luck and thanks for using fixya

Hello,

When you put it to drain/spin does the pump make any attempt to drain,if not it could be that there is something stuck in the pump,needs draining manually.Another thing to try is to find the fault code.If you hold down the 2 buttons on the far right of panel then press on/off button till lights start chasing,then release the 2 buttons on right hand side.Now the first function button by the on/off button you will need to press until the light above the button reaches the 9th or 10th position this will give you a read out in the display.
E10 = low water press.
E20 = pump or filter.
E30 = press. switch or heater faults.
E40 = Door swich.
E50 = motor.
Some of these numbers can vary there are more but those are the most common.After checking codes switch off machine then back on twice to reset.

Hope this helps.

Hi!

F09 code on your whirlpool means---

Overflow Condition
If the Overflow contact on the pressure switch is Closed for more than 60 seconds and Overflow condition will occur. In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly. Try pressing PAUSE/CANCEL twice to cleaar the Display.

If display doesn't gets cleared then check for---

• Check the drain hose and make sure it is not plugged or kinked.
• Check Wire Harness connectors to the Drain Pump.
• Pressure Switch, and Central Control Unit (CCU)
• Check/Clean Drain Pump Filter of foreign objects
• Check for Drain Pump Failure
• Check the Inlet Valve for proper shut off
• Check the Pressure switch for proper operation

Please rate this solution as Fixya if found useful.

Please ask for any clarifications.

Thanks
Rylee

Do you have any error codes?

Does water remain in the washer after the final spin?
If water remains in the washer after the final spin, then the door will not unlock. Drain/Spin or Spin Only to remove any remaining water from the washer. The door should unlock at the end of the cycle.
Is the door locked and the Add A Garment light on?
If the Add A Garment light is on, then the washer door will unlock after the Pause/Cancel button is pressed once. Pressing the Start button will restart the washer at the same point where it left off in the cycle.
Is the door locked and the Add A Garment light off?
If the Add A Garment light is off, then the washer door will unlock after the Pause/Cancel button is pressed twice. The door will not immediately unlock while the cycle is running due to a possible high-water level in the washer, high-water temperature, tumbling or spinning. It may take up to five minutes for the washer to stop spinning and draining before the door will unlock. You will hear the door click when it unlocks.
If Pause/Cancel does not work:

1. Unplug washer or disconnect power for one minute.
2. Plug in washer or reconnect power.
3. Re-select the cycle and press Start.

NOTE: If the error remains on the display, call for service.

This is what F09 means

Condition
Overflow Condition
If the Overflow contact on the pressure switch is Closed for more than 60 seconds and Overflow condition will occur. In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Unplug the unit to service.



Check and repair

• Check the drain hose and make sure it is not plugged or inked.
• Check Wire Harness connectors to the Drain Pump, Pressure Switch, and Central Control Unit (CCU)
• Check/Clean Drain Pump Filter of foreign objects
• Check for Drain Pump Failure
• Check the Inlet Valve for proper shut off
• Check the Pressure switch for proper operation

Hold down the Display/Menu function button (one of those three buttons on the left of the unit) for about 3-4 seconds until the display reads "t set". When this appears, push the track forward button once (>>|) so the display reads "beep"; now press the play pause button (>||) once. The display will now say "on", push the track forward button (>>|) once to make it read "off"; now push the stop play button. You're done. Enjoy the silence.