How to replace outside drivers side door handle on a 2000 chevy silverado i took the panel off need to know what to do next

Search Results

How To Install Replace Inside Door Handle Chevy Equinox ...

? 9:02
https://www.youtube.com/watch?v=cY6asyM2R6g
Feb 2, 2012 - Uploaded by 1A Auto Parts
How To Install Replace Inside Door Handle Chevy Equinox 05-09 1AAuto.com .... found your tutorial on fixing my driver's side door handle for my 2006 Equinox. .... Door Handles Chevy Equinox 2010 2011 2012 GMC Terrain ...

How To Install Replace Inside Door Handle 2007-13 ...

? 9:05
https://www.youtube.com/watch?v=QonKLwhk2CE
Apr 2, 2015 - Uploaded by 1A Auto Parts
http://www.1aauto.com/interior-door-handle-driver-side-front/i/1adhi00417 1A Auto shows you how to repair, install, fix,change or replace a broken or snappe... ... 10, 11, 12, 13 Chevy Silverado, Tahoe, Suburban and GMC Sierra, Yukon Denali ...2007-2011 Tahoe Yukon Suburban Escalade Vent Section ...Missing: terrain

How To Install Remove Rear Outside Door Handle 2007-13 ...

? 10:02
https://www.youtube.com/watch?v=7ZUTqqEzpZg

take door panel off there is nuts holding handle on door and 2 rods one to lock and one to handle to open door

the linkage behind the handle either the retaining clip broke or popped off need to remove the door panel to check and fix

Bring the vehicle into the dealer if you have a sticky gas pedal. This is a TOYOTA PROBLEM.
Door handle:
It easy ! You need a philips and flat screw driver,and a needle nose pliar.
Use flat screw driver and pry out the two or three dust covers for the arm rest screws then use philips and remove the screws. Next use the flat screw driver and pry out the black plastic mirror cover from the inside of the door. Pry out the switch with the flat screw driver and disconnect it. On the side of the door panel just above the striker/loch mechanism is this plastic push pull type of a hold in screw. Use flat screw driver to get it to move a little then pull it out with the needle nose. Depending on which door your doing if you have a map folder in the door there are two more screw to remove on the bottom of the door.
Now the inside door handle is tricky it comes out in TWO pieces. Use philips and get the only hold down screw you see out.( you may have to pry out a little screw cover first) Now the inside door handle cover is removed by placeing the flat screw driver on the rear of the outside of the cover top and on the outside rear bottom to release the tangs that are holding it onto the panel.Pry it out lightly you may have to place the screw driver over the top of the door release button and pry that way. Don't loose your cool its a pain but it will fall out. Once its removed unhook the panel.

Next lift the plastic cover and remove the door handle hooks and levers . Basically use common sense this is easy stuff. There may be two screws from inside of door panel that keep handle in place . Then work handle loose from outside and inside . reverse for installation.

Hi those are somtimes a pain ,I,m not sure which part your at on your job but once you release the linkage that is attached inside your door panel then you should be able to remove the nuts or screws that hold the door handle in from the inside then when you get the handle out from the truck then remove the lock ,also put some masking tape around the paint on the outside of the door ,because when remove the handle from the door and putting it back in you may have to angle the handle a bit for it to fit back into place ,sometimes a long pick with a 45degree tip on it helps alot when removing the inside linkage ,hope this helps ,let me know if I can help further!

I have shaved door handles on a 2000 chevy silverado and the drivers side door just recently stopped opening it seems like its completely locked out and the door is closed so i cannot get to the bolts of the latch assembly when i hit the unlock button it unlocks half way and when you go to open the door it relocks itself even if you manually try to unlock the door and hold the lock forward it still wont open

Remove screw from inside door grab handle. Remove door panel by carefully prying out plastic clips. Drill or chisel off pop rivets holding the handle on. Pull handle out far enough to disconnect linkage and remove handle. Install new handle and secure to metal panel with new pop rivets or sheet metal screws. It may be easier to reconnect linkages by removing the metal panel also.

unscrew the old handle and screw a new one in place

If you have the panel off, just look up at were the outside door handle is mounted. You need to unbolt the rest of what is left....usually a metric fastner. Next, there should be 2 small access holes, probably covered by plastic sheeting. These holes are for the socket to reach them. There are a few clips that need to be popped loose from the rods but take your time and use a thin flat tipped screwdriver. And when you go to reinstall the new handle, you'll have to manipulate the handle into the door skin or the "hole" where the door handle goes.

Just take your time and you can do this.

Good luck!

There should be a set of fasteners holding the handle in place, probably 2 nuts or more. Use a light to see inside the door handle area to examine the fasteners. Having a replacement part will also help, sometimes it has instructions. At the least you can see the entire handle part and understand how it's mounted in the door.