Were is the egr valve located on 95 maxium - 1995 Nissan Maxima

fixya answer on a 97 ram

97 dodge ram 1500 shakes at 45 55 mph after overdrive

this is the EGR part for a 95 ram

DODGE PICKUP RAM 1500 EGR Valve from Best Value Auto Parts

Please look at the following diagram to identify the engine sensors of RAV4 3RZ-FE.

Hope that works. Thank you for visiting Fixya.

It is located between the EGR valve and the intake vacuum source, one line gores to a vacuum port on the intake and the other to the EGR valve, just follow the lines.

Sorry I dont have a pic. for you. But here are instructions. The EGR valve is located at the top right of the engine next to the throttle body. REMOVAL & INSTALLATION
Except Linear EGR Valve

Disconnect the negative battery cable.
Remove the air cleaner assembly from the engine.
If equipped, unplug the valve electrical connection.
Remove the EGR valve vacuum tube from the valve.
Remove the EGR bolts and/or nuts and remove the EGR valve and gasket.
To install:
Install a new gasket to the EGR valve and install the EGR valve to the manifold.
Install the nuts and/or bolts. Tighten the bolts to 17 ft. lbs. (24 Nm) and the nuts to 15 ft. lbs. (20 Nm).
Connect the vacuum tube to the EGR valve.
If equipped, attach the valve electrical connection.
Install the air cleaner and connect the negative battery cable.
Linear EGR Valve
Disconnect the negative battery cable.
Note the position of the EGR valve prior to removal. Do not rotate the valve 180?.
Unplug the valve electrical connection..
Unfasten the valve retainers, then remove the valve and the gasket.

To install:
Clean all gasket residue from the gasket mating surfaces.
Install a new gasket and the valve.
Install the valve retainers.
On 1994-97 2.2L engines and 1994-95 4.3L engines, tighten the valve retainers to 17 ft. lbs. (24 Nm). On 1998-99 2.2L models, tighten the retainers to 19 ft. lbs. (26 Nm).
On 1996-99 4.3L models, tighten the retainers on the first pass to 89 inch lbs. (10 Nm) and on the final pass to 18 ft. lbs. (25 Nm).
Attach the valve electrical connections and connect the negative battery cable.

Check this VIDEO for removing, cleaning, and reinstalling the EGR valve on my 95 Toyota Tercel.




Hope helps (remember to rate this answer).

The EGR valve is located on the rear right area of the intake manifold. The egr valve connected to the right exhaust manifold.It is connected via a metal tube. The valve and the tube has to be removed as an assembly, and separated once it is off the car. The EGR stands for Exhaust Gas Recirculation. It is part of the vehicle emissions system.There are generally three parts to the EGR system: the EGR Valve, an actuator solenoid, and a pressure sensor EGR (DPFE). These things work together.They are easily cleaned by removing the cover on the rear of the intake manifold. these ports are small, and easily clogged by carbon, and oil residue.There are two ways to replace the egr valve. To replace the EGR valve get ahold of a 11mm Gear Wrench and do it from the top. Or If you have a lift, the jack up the vehicle of jack stands and you can drop the exhaust from the bottom and get it that way. -------------- Keep updated for any further queries.Thanks.

egr transducer solenoid,,located at underhood, beside a/c idle up solenoid control, take alook at the vaccum hose at egr valve, its goes through the egr solenoid treansducer valve, picture later

EGR valve is located on the intake, isually a circular unit with a pipe connecting to the exhaust. As for the knock sensor, this is below the intake and hard to access w/o removing the intake. Both of these if failing need replacement, never replace with used ones. Hopefully this helps!!

The EGR valve is located on the rear passenger side of the Intake.

Should be close to your throttle body, usually held by 2 big screws, disconnect the hose coming from egr valve, and replace with a new one, dont lose the gasket.