How do i remove bench seat in 66 mustang - 1966 Ford Mustang

Question edited for FULL 'year MAKER model'.
Question moved from Spanish car maker 'Seat' pronounced 'see-at' to correct category.

See videos and articles

https://www.google.com/search?q=1990+Mitsubishi+Montero.+remove+the+rear+bench+seat

..

check the bottom front side of bench seat.
look to see if pull out tabs '
lift.
see
https://www.autoinstruct.com.au/manufacturer/holden/ve-commodore/removing-rear-seat/
for full tutorial

You need to remove the seat bottom first to access the lower attaching points.

THERES BOLTS EITHER ON THE BOTTOM LIKE A FOOT AWAY FORM THE DOOR, OR THERE GONNA BE BETWEEN THE BOTH SEATS BY WHERE YOUR SEAT BELS GO IN. YOU HAVE TO PUSH OPEN IN THERE AND YOULL SEE THEM THEY SOME TIME HOLD THE SEAT BELST ALSO AS WELL AS THE SEAT.

Remove windshield and rear window to do it properly. Headliner is actually crimped in between window gaskets and roof edge. Not a job for the faint at heart. If you don't know the string trick to get your gaskets in place you'll be working on it this time next year. Look on CJ Pony parts web site. They used to have a good tech article on headliner replacement. Hope this helps...

REMOVAL & INSTALLATION

1. Clamp the seat belts to keep them from retracting.
2. Locate and disconnect seat wiring at the connector(s).
3. Move front seats forward or back for access to the hold down hardware.
4. Put the rear seats in the stowed position.
5. On Durango 3rd row seats, lift the cushion upward and forward to floor cargo position.
6. Remove the hardware securing the seat.
7. On split bench models, lift the center seat upward to clear attachment stud
8. Remove the seat from the vehicle.

NOTE Do NOT activate the track adjusters once the fastening hardware is removed.

1. Installation is the reverse of removal.

Fig. Disconnect the wiring from under the seat




Fig. Seat track mounting hardware locations-typical




Fig. Bench seat components: seat (1), nut (2), stud (3), floor pan (4), bolt (5)-Ram




Fig. Split bench seat assembly-Ram




Fig. Bucket seat mounting components-Durango shown




Fig. Rear seat removal/installation


I hope help you with this; good luck (rated this help).

please rate highly if this is what you need

Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Cushion, Rear Removal and Installation

1. Release pin from locks by pressing release button under rear seat cushion.

1. Pull rear safety belt and buckle (60044) through openings in rear seat cushion pad and frame (600A88) and remove rear seat cushion pad and frame .

1. To install, reverse Removal procedure.
   

----------------------------------------------
Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Back, Rear Sedan
Removal

1. Remove rear seat cushion as outlined.

1. Remove rear seat bolster. Refer to Section 01-05 .

1. Remove rear seat bolster mounting bolts. Remove bolster assembly.
2. Remove four seat back to package tray retaining bolts.

1. Remove seat back.

1. To install, reverse Removal procedure.

it is not designed to be removed. It is designed to slide back and forth as needed.

Section 01-10: Seats and Tracks 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Seat, Rear Bench
Removal

1. Remove the center seat(s) if equipped. Refer to the procedure in this section.
   

1. Slide the bench seat forward to the center row seating position.
   

1. Use a flat-blade screwdriver to remove the cover caps from the front of the rear seat cushion latch cover.
   
   
   
   
   

1. Remove the two rear seat bolts from the front of the rear seat cushion latch cover.
   
   
   
   
   

1. Lift the rear seat cushion floor cover on the back of the rear bench seat and remove the two inboard rear seat bolts and the two outboard rear seat bolts.
   
   
   
   
   

1. Remove the bench seat from the vehicle through the body side door opening.
   

the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

Seat —Third Row Bench Removal
CAUTION: Removal of the third row bench seat requires more than one technician.

1. Remove the second row seats. For additional information, refer to Seat—Second Row .

1. Remove the floor mats.

1. Lock the seat cushion in the upright position.
   1. Lift the handle to release the cushion.
   1. Lock the seat cushion in the upright position.

1. Move the third row bench seat to the second row position.
   • Lift the seat track release handle.

1. Remove the two bolt covers.

1. Remove the two seat track front bolts.

1. Remove the four seat track rear bolts.
   1. Position the rear seat cushion floor cover aside.
   1. Remove the four seat track rear bolts.

1. Remove the third row bench seat.

Hi pgarrity,hope this helps my friend good luck,this is simplified :)