Question about 2004 Ford Mustang

1 Answer

Mustang rear seat removal?

How do I remove a rear seat from a 2004 Ford Mustang Coupe?

Posted by countrygrl31 on

Ad

1 Answer

gerry bissi

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 4,388 Answers

Please rate highly if this is what you need

Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Cushion, Rear Removal and Installation

  1. Release pin from locks by pressing release button under rear seat cushion.
  1. Pull rear safety belt and buckle (60044) through openings in rear seat cushion pad and frame (600A88) and remove rear seat cushion pad and frame .
  1. To install, reverse Removal procedure.
----------------------------------------------
Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Back, Rear Sedan
Removal
  1. Remove rear seat cushion as outlined.
  1. Remove rear seat bolster. Refer to Section 01-05 .

  1. Remove rear seat bolster mounting bolts. Remove bolster assembly.
  2. Remove four seat back to package tray retaining bolts.
  1. Remove seat back.
  1. To install, reverse Removal procedure.

Posted on May 05, 2009

Ad

5 Related Answers

Gozer

Mike Raatz

  • 435 Answers

SOURCE: how do i remove the back seat to my 2000 ford

On the seat bottom left and right of center there's a release clip. (see photo) Carefully push the release with a flat screw driver and pull up doing one side at a time.
Once the seat bottom is removed there's 2 bolts holding the seat back in place, remove the bolts and lift the seat back straiting up.


a2d03ac.jpg

Posted on Jun 08, 2010

Ad
emissionwiz

Marvin

  • 85239 Answers

SOURCE: how do I set the clock on my 2003 Ford Mustang 2 door coupe

Here is a link to your owners manual at Fords web site, download it and look on page 22 for the procedure to set the clock.

http://www.motorcraftservice.com/pubs/content/~WO3MUS/~MUS~LEN/42/03musog5e.pdf

Posted on Nov 13, 2008

gerry bissi

  • 4388 Answers

SOURCE: rear wheel bearing

SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal

  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.
  1. Remove the differential pinion shaft (4211).
    1. Remove the differential pinion shaft lock bolt (4241).
    1. Remove the differential pinion shaft.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Remove the U-washer (4N237).
    1. Push the axle shafts (4234) inboard.
    1. Remove the U-washer.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
    Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Remove the axle shaft.
--------------------------------------------------------------------------------------
Rear Wheel Bearing and Axle Shaft Oil Seal Removal
  1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.
  1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.
Installation
  1. Lubricate the new rear wheel bearing with the specified lubricant.
  1. Using the special tools, install the new rear wheel bearing.
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the new wheel bearing oil seal.
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

-------------------------------------------------------------------
Installation
  1. Lubricate the lip of the wheel bearing oil seal
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Install the two axle shafts.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Install the U-washer.
    1. Position the two U-washers on the button end of the axle shaft.
    1. Pull the axle shaft outward.
  1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
    Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the case lock bolt hole.
    1. Install a new differential pinion shaft lock bolt.
  1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
  1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. Install the rear brakes. For additional information, refer to Section 206-04 .
  1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .
  1. Lower the vehicle.

Posted on Apr 10, 2009

Anonymous

  • 3741 Answers

SOURCE: how to remove rear seat back 1987 mustang

Tools Required:

  • 3/8 inch Drive Ratchet
  • 3/8 inch Drive 3” Extension
  • 3/8 inch Drive 10mm Socket
  • 3/8 inch Drive 13mm Socket
  • T-50 Torx Bit
  • 1/4 inch Allen Wrench
  • 3/16 inch Allen Wrench
  • 1/2 inch Wrench
  • Drill Motor
  • 1/8 inch Drill Bit
  • 5/16 inch Drill Bit
  • 2 inch Hole Saw
  • Trim Tool (Fork Tool)
  • Electrical Tape
  • Center Punch
  • Hammer
------------------- Installation:

Remove Back Seat:
  1. Locate the retainers securing the seat bottom into the vehicle, approximately 10 inches from the end of the cushion, either side. Use your thumb to push in retainer release tab. Lift the seat up to remove.
  2. Remove the two 13mm screws securing the seat back, located on each lower corner. Lift seat upward to release seat back from brackets at the top. You can carefully prop the seat back under the retracted top , use caution if choosing this method not to damage or scratch the vinyl of the seat. You can remove the seat from the vehicle completely by disengaging the flanges securing the top of the rear seat to the fabric of the convertible top well .
  3. Remove Quarter Trim Panels:
    1. Grip the Quarter Trim Panel Cap at the shoulder strap opening and lift up to dislodge the retaining clips.
    2. The inside Quarter Trim Panels are two-piece panels. Remove the upper portion of the Quarter Trim Panel from the vehicle; it is not necessary to remove the lower portion. Pull the forward edge of the trim Panel over the pinch weld in the doorjamb.
    3. Use a Door Trim Tool (Fork Tool) to dislodge the pushpin retainer at the rear edge of the Trim Panel approximately 4” down from the top, pry Trim Panel toward the outside of car to release retainer.
    for more help click this link directly
    1. http://www.americanmuscle.com/05-07-lightbar-install.html ---------

Posted on Oct 05, 2009

Pops65Pony

Tom Shanks

  • 138 Answers

SOURCE: Headliner install in 66 mustang coupe

Remove windshield and rear window to do it properly. Headliner is actually crimped in between window gaskets and roof edge. Not a job for the faint at heart. If you don't know the string trick to get your gaskets in place you'll be working on it this time next year. Look on CJ Pony parts web site. They used to have a good tech article on headliner replacement. Hope this helps...

Posted on Mar 10, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove hydraulic lift cylinder from 2001 mustang conv V6


need to remove all plastic panels on the rear seat remove seat and remove the convertible top assembly complete

Sep 09, 2014 | 2001 Ford Mustang Convertible

1 Answer

How to remove rear seat on 2003 mustang convertible


There are two latches for a full size seat. One on each side of the car. Grab the seat and push back towards the truck and pull it up at the same time. they can be difficult. Some of the older models have bolts you have to remove. Run your fingers under the seat, they are located in the middle of where you sit.

May 12, 2014 | 2003 Ford Mustang

2 Answers

2004 ford mustang coupe brake lights dont work dont have manual to change the fuse


pull out 1 fuse at a time and look at the wire trace inside if it looks broken or black, replace it. if it looks good. put it back in and keep trying

Jul 31, 2010 | 2004 Ford Mustang

1 Answer

Remove rear seat back of 65 Mustang


push in and up on bottom of seat then remove bolts to remove the back

Jul 12, 2010 | 1965 Ford Mustang

1 Answer

I NEED TO REMOVE THE FRONT SEAT HEADRESTS FROM A 2004 FORD MUSTANG CONVERTIBLE.


Lift the headrest to it highest postion. Insert a thin stick parallel to the head rest bar (the side facing the rear of the vechicle) I used a thin paint stirring stick, a Slim Jim is ideal.
Once the stick is inserted (10" give or take) push the head rest down holding the stick steady, then pull the headrest back up and it will come off the seat.
Hope this helps.

Apr 03, 2010 | 2004 Ford Mustang

1 Answer

How do you remove 89 convertible mustang rear seat


hit it hard (with the side of your hand or palm) at the bottom of the seat on the right and the left to relase the spring retainers, run a putty kniofe under the seat edge to locate the spring retainers

Apr 02, 2010 | 1989 Ford Mustang

1 Answer

Headliner install in 66 mustang coupe


Remove windshield and rear window to do it properly. Headliner is actually crimped in between window gaskets and roof edge. Not a job for the faint at heart. If you don't know the string trick to get your gaskets in place you'll be working on it this time next year. Look on CJ Pony parts web site. They used to have a good tech article on headliner replacement. Hope this helps...

Feb 22, 2010 | 1966 Ford Mustang

1 Answer

How do you install 1965 mustang quarter panel


Remove rear seat and interior side panels. You'll see nuts on the posts for the trim pieces.

Oct 13, 2009 | 1965 Ford Mustang

4 Answers

How do you remove the front seats from a 1965 Mustang? do you go up from underneath the car?


NO. there will be 4 bolts under each seat, pull the seat all the way forward and remove the rear 2 bolts at each end of the seat track, then push the seat all the way back and remove the 2 front bolts.

Sep 27, 2009 | 1965 Ford Mustang

1 Answer

2001 mustang seat belt locked up and will not let it go forward


2001 mustang coupe

the right back seat seat belt is locked up.

will not retract or let more belt out

Jul 20, 2008 | 2001 Ford Mustang

Not finding what you are looking for?
2004 Ford Mustang Logo

Related Topics:

1,216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14866 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...