1992 mits 2.4 L pickup [ new ecm,fuelpump,fuel pump]

if spark and fuel possible belt improperly replaced - timing maybe off--ecm not flashed correctly for vehicle

Crank position sensor does not make the fuel pressure.
Is the fuel pump running at switch on ... if not check the trouble codes and act on the findings.

Sure the new coil is working? Did you check for spark?Is the fuel pump working? Fuel injectors? ECM?

Dodge Dakota Crank No Start Fix - YouTube

? 8:10
https://www.youtube.com/watch?v=a-rfAd0YLg0
Jun 29, 2014 - Uploaded by AJ Pierce
In this video, I will show you how I fixed my 1992 Dodge Dakotanot starting. ... Engine cranks but won't start - Duration: 18:30. jimthecarguy ...

Inspect Fuses if Engine Cranks But Does Not Start : Dodge ...

repairpal.com > Problems > Dodge > Dakota

Engine Will Not Start Due to Blown Door Lock Fuse on Dodge Dakota ... cap and rotor, wires, plugs, coil, fuel pump assy, coil pickup sensor, crank position sensor and have new ECM on the way, Cranks but won't fire. ... 1990 Dodge Dakota.

Dakota won't Start - Discussion on Topix

www.topix.com > Dodge Dakota

Jan 22, 2009 - have a 1993 dodge dakota sport that wont start. when you turn the key on there is no power to the fuel pump and does not fire. any ideas ... I just bought a1990 Dodge Dakota Sport 4x4 5-Speed, there is only one problem, it only .... I went to move it the other day, it would turn over, but had no spark or gas.

Dodge Dakota Questions - PROBLEM STARTING - CarGurus

www.cargurus.com > Questions > Dodge > Dakota

CarGurus

if there is no power to the fuel pump check relays and fuses....UNDERHOOD FUSE & RELAY PANEL IDENTIFICATION Fig. 2: Underhood Fuse & Relay Panel Identification Courtesy of ISUZU MOTOR CO. Fusible Link Identification ? A - 80 Amp (1991-92 3.1L) ? A - 60 Amp Main-1 ? B - 30 Amp Main-2 ? C - 30 Amp (1993-94) ECM (3.2L) ? D - 30 Amp Condenser Fan (A/T Models) Relay Identification ? 1 - Headlight Relay ? 2 - A/C - Heater Relay ? 3 - Starter Relay ? 4 - A/C Compressor Relay ? 5 - Charge Relay ? 6 - Fuel Pump Relay ? 7 - ECM Relay ? 8 - Wiper Relay Fuse & Circuit Breaker Identification ? 1 - 15 Amp (1991) ECM, Fuel Injection System ? 1 - 15 Amp (1992-94 2.6L) ECM, Fuel Injection System ? 1 - 10 Amp (1992-94 3.1 & 3.2L) Heated Oxygen Sensor, Fuel Injection System ? 2 - 20 Amp (1991-92) Fuel Pump ? 2 - 20 Amp (1993-94 2.6L) Fuel Pump ? 2 - 15 Amp (1993-94 3.2L) Fuel Pump ? 3 - 10 Amp (1991) ? 3 - 15 Amp (1992-94) Turn Signal Lights, Hazard Warning Flasher Lights ? 4 - 10 Amp Horn, Door Locks ? 5 - Not Used (1991 3.1L) ? 5 - 10 Amp Charging System, Charge Warning Light WARNING: Always disconnect battery ground cable before servicing "high- current fuses. It is recommended that "high-current" fuses be replaced by a qualified technician. Page 1 of 2 FUSES & CIRCUIT BREAKERS -1994 Isuzu Rodeo LS? 6 - Not Used (1991) (1992-93 2.6L) ? 6 - 10 Amp (1992-94 3.1L & 3.2L) A/T Interlock System ? 6 - 10 Amp (1994 2.6L) Heated Oxygen Sensor, Fuel Injection System ? 7 - 20 Amp Heater/Air Conditioning Blower Controls ? 8 - 10 Amp Air Conditioner Compressor Controls ? 9 - 10 Amp Right Headlight ? 10 - 10 Amp Left Headlight © 2008 Mitchell Repair Information Co., LLC.

Underhood fuse block swap out relay #7 thats the ECM relay.
Ground Circuits Using a DVOM, touch negative voltmeter lead to a good ground. Touch positive voltmeter lead to each ground terminal. With vehicle running, voltmeter should indicate less than one volt. If reading is greater than one volt, check for open, corrosion and loose connection on ground lead. See ECM GROUND LOCATION table for ECM ground location.
Page 1 of 1 SYSTEM/COMPONENT TESTS - 2.6L EFI -1994 Isuzu Rodeo

Have the crank shaft sensor check out. This is a beginning of the problem. After that it will never be able to start since the ECM doesn't know what the position of the piston reported through the crankshaft sensor to turn on the proper ignition. Good luck.

TRY REPLACING THE FUEL PUMP RELAY. THIS SHOULD SEND POWER TO THE PUMP. IF NOT, THEN CHECK THE WIRING HARNESS NEAR THE FUEL TANK. I HOPE THIS HELPS. P.S.: IF I REMEMBER CORRECTLY, THE PCM IS RESPONSIBLE FOR THE FUEL PUMP OPERATION. THANKS FOR USING FIX-YA. PLEASE KEEP ME POSTED. GOOD LUCK

check all those item again, especially the crank sensor, check the fuel pump by adding 12v to it, make sure its good. tun on key, make sure your getting 12v from fuel pump wire

Check fuel filter and air cleaner, fuel pump or fuel pump relay

http://www.stealth316.com/2-fuelpump.htm