Question about 1993 Isuzu Rodeo
We had the same problem,3 years of every now and then working on it.new ecm lots of other parts,changed ecm relay fuse, started right up.
Posted on Sep 10, 2013
If there is no power to the fuel pump check relays and fuses....UNDERHOOD FUSE & RELAY PANEL IDENTIFICATION Fig. 2: Underhood Fuse & Relay Panel Identification Courtesy of ISUZU MOTOR CO. Fusible Link Identification ? A - 80 Amp (1991-92 3.1L) ? A - 60 Amp Main-1 ? B - 30 Amp Main-2 ? C - 30 Amp (1993-94) ECM (3.2L) ? D - 30 Amp Condenser Fan (A/T Models) Relay Identification ? 1 - Headlight Relay ? 2 - A/C - Heater Relay ? 3 - Starter Relay ? 4 - A/C Compressor Relay ? 5 - Charge Relay ? 6 - Fuel Pump Relay ? 7 - ECM Relay ? 8 - Wiper Relay Fuse & Circuit Breaker Identification ? 1 - 15 Amp (1991) ECM, Fuel Injection System ? 1 - 15 Amp (1992-94 2.6L) ECM, Fuel Injection System ? 1 - 10 Amp (1992-94 3.1 & 3.2L) Heated Oxygen Sensor, Fuel Injection System ? 2 - 20 Amp (1991-92) Fuel Pump ? 2 - 20 Amp (1993-94 2.6L) Fuel Pump ? 2 - 15 Amp (1993-94 3.2L) Fuel Pump ? 3 - 10 Amp (1991) ? 3 - 15 Amp (1992-94) Turn Signal Lights, Hazard Warning Flasher Lights ? 4 - 10 Amp Horn, Door Locks ? 5 - Not Used (1991 3.1L) ? 5 - 10 Amp Charging System, Charge Warning Light WARNING: Always disconnect battery ground cable before servicing "high- current fuses. It is recommended that "high-current" fuses be replaced by a qualified technician. Page 1 of 2 FUSES & CIRCUIT BREAKERS -1994 Isuzu Rodeo LS? 6 - Not Used (1991) (1992-93 2.6L) ? 6 - 10 Amp (1992-94 3.1L & 3.2L) A/T Interlock System ? 6 - 10 Amp (1994 2.6L) Heated Oxygen Sensor, Fuel Injection System ? 7 - 20 Amp Heater/Air Conditioning Blower Controls ? 8 - 10 Amp Air Conditioner Compressor Controls ? 9 - 10 Amp Right Headlight ? 10 - 10 Amp Left Headlight © 2008 Mitchell Repair Information Co., LLC.
Underhood fuse block swap out relay #7 thats the ECM relay.
Ground Circuits Using a DVOM, touch negative voltmeter lead to a good ground. Touch positive voltmeter lead to each ground terminal. With vehicle running, voltmeter should indicate less than one volt. If reading is greater than one volt, check for open, corrosion and loose connection on ground lead. See ECM GROUND LOCATION table for ECM ground location.
Page 1 of 1 SYSTEM/COMPONENT TESTS - 2.6L EFI -1994 Isuzu Rodeo
Posted on Mar 28, 2010
if you have no power when driving or acceleratiing it could be the fuel filter if not replaced could be clogged up. if your getting good fuel pressure to the engine could need a tuneup. if your not getting power to the pump and it plugged in check the ground wire going to the frame from the pump could have a bad contact.
Posted on Aug 28, 2009
well i got a salvaged ecm from a junkyard and put it in, still did'nt start. took alternator off to have it checked , it is fine. put it back in and now it starts and runs fine. check the alternator and the connections, i heard the alternator controls power after the initial ecm prime when it is turned on. i have no idea how true it is, but worth a shot. if you can find a cheap ecm for a junkyard (mine was 75 bucks) i would try that afterwords.
Posted on Mar 06, 2009
Have you checked for an exhaust restriction? Most garages and exhaust shops can perform a back pressure test for a minimal fee.
Posted on May 12, 2011
Testimonial: "I will try this.. Best lead so far."
Tips for a great answer:
Apr 22, 2011 | 1991 Isuzu Rodeo
Mar 21, 2011 | 1993 Isuzu Rodeo
Jun 10, 2010 | 1993 Isuzu Rodeo
Jul 01, 2009 | 1997 Isuzu Rodeo
Jul 27, 2008 | Isuzu Rodeo Cars & Trucks
1,963 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: