Ariston Technologies Recent Questions, Troubleshooting Help & Support

F10: Pressure Switch Empty and Full or neither Empty nor Full Pressure Switch Found Overhaul CN1 Overhaul Pressure Switch Wiring Control CN1/Pressure Switch Continuity Replace Pressure Switch Replace Card Dado

F01: Triac Short circuit Overhaul CNE Replace Card Dado

The washing machine fails to load water (The wording H20 is displayed). • The water inlet hose is not connected to the tap. • The hose is bent. • The water tap is not turned on. • There is a water shortage. • The water pressure is insufficient. • The START/RESET button has not been pressed. Dado

The washing machine fails to load water (The wording H20 is displayed). • The water inlet hose is not connected to the tap. • The hose is bent. • The water tap is not turned on. • There is a water shortage. • The water pressure is insufficient. • The START/RESET button has not been pressed. F01: Triac Short circuit Overhaul CNE Replace Card Dado

F13: NTC wiring harness disconnected from the dryer system 1. Check the efficiency of the terminals on the CNA connector board 2. Check NTC wiring harness 3. Check the wiring harness continuity of the CNA / NTC connectors 4. Replace NTC 5. Replace terminal board Dado

F04: Overflow and Pressure Switch Empty found at the same time (Pressure Switch stuck on Empty) Overhaul CN1 Overhaul Pressure Switch Contacts Control CN1/Pressure Switch Continuity Replace Pressure Switch Replace Card Dado

F12 SPECIFIC FOR LVB2000 INDESIT EVOLUTION / DIALOGIC. F12: Lack of Display card-Main Card Communication 1. Check the effectiveness of contacts on CNC Connector Card 2. Overhaul 8-way connector on Display card 3. Check continuity of CNC-CN 8 way connector 4. Replace Main Card 5. Replace Display Card Dado

The washing machine fails to load water (The wording H20 is displayed). • The water inlet hose is not connected to the tap. • The hose is bent. • The water tap is not turned on. • There is a water shortage. • The water pressure is insufficient. • The START/RESET button has not been pressed. Dado

The washing machine fails to load water (The wording H20 is displayed). • The water inlet hose is not connected to the tap. • The hose is bent. • The water tap is not turned on. • There is a water shortage. • The water pressure is insufficient. • The START/RESET button has not been pressed. Dado

The washing machine fails to load water (The wording H20 is displayed). • The water inlet hose is not connected to the tap. • The hose is bent. • The water tap is not turned on. • There is a water shortage. • The water pressure is insufficient. • The START/RESET button has not been pressed. Dado

F02: Blocked Motor, Short-circuited/Open Tachometry Overhaul CNE Overhaul Motor connector Control CNE Continuity/Motor Connector Control Motor Windings Control Tachometry Windings Replace Card Dado

F05: Blocked Pump or Pressure Switch stuck on Empty Found Overhaul CNF (pump connector) Overhaul Pump Connector Control Pump Filter Control Pump Windings Change Pump Replace Card Dado

The washing machine fails to load water (The wording H20 is displayed).

• The water inlet hose is not connected to the tap.
• The hose is bent.
• The water tap is not turned on.
• There is a water shortage.
• The water pressure is insufficient.
• The START/RESET button has not been pressed.

Dado

F11: Pump Feedback Missing Overhaul CN1 Overhaul CNF Overhaul Pump Connector Overhaul Pressure Switch Connector Control Pump Windings Replace Pump Replace Card Dado

F01 - Electronic circuit board fault Issue: Washing machine is not operating - some or all functions are not selectable. Cause: Main module, triac on board damaged or components feedback fault Advice: We recommend you disconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Reconnect supply and wait 30 seconds and try starting the machine again. Dado

I had this issue also and it was because I started the machine and had not turned on the water to it. However, it cleared when I unplugged the power cord, waited about ten seconds, then plugged it back in. I guess they need a "reboot" once in awhile, like a computer - at least mine did. Hope this works for you, too.

This should do it. http://www.manualslib.com/products/Ariston-Avxl-105-3182207.html Ariston AVXL 105 Manuals

It means "heater relay cannot be activated". Troubleshooting guide says to tap the relays to try to unjam them. If that fails, replacement of the main control board is necessary. These washers apparently have a propensity for stuck relays on the newer units.

water h2o is symbel for water