Ariston Technologies Logo

Ariston Technologies Answered Questions & Fixed Issues

Do you work here? Claim your company

  • 31 Products
  • 1K Answers

Tia The above answer would be helpful but I’m trying to get my dishwasher to drain & this makes the dishwasher do some type of cycle & doesn’t drain at all... pls advise

Ariston... | Answered on Apr 16, 2020 | 231 views

According to the instruction book - it appears the machine has been stopped mid cycle then re-started.
Switch machine off, turn control knob to a solid circle symbol (they are after every set cycle). Switch machine back on and lights will flash and program is reset. You can then select wash cycle as normal.

Ariston... | Answered on Mar 16, 2020 | 3,111 views

Pump fault or more likely blocked filter try cleaning should reset it self

Ariston... | Answered on May 06, 2019 | 4,118 views

If it is a child lock, normally by pressing and holding the Child Lock Button. Sometimes it requires two buttons, from Off, press and hold the On button and the Child Lock button for 6 seconds.

For other lock problems, see the videos

Ariston... | Answered on Feb 24, 2019 | 104 views

F06: Selector Error
Overhaul CND (selector connector)
Overhaul Selector Connector
Control Selector/CND Continuity
Control Selector Motor
Replace Selector
Replace Card


Ariston... | Answered on Jan 06, 2019 | 1,038 views

did you check breaker in breaker panel

Ariston... | Answered on Jan 05, 2019 | 55 views

Ariston... | Answered on Dec 16, 2018 | 229 views

Has anyone got manual for ariston K-LB 121?

Ariston... | Answered on May 02, 2018 | 102 views

when I wash heavy stuff it will not spin properly because the weight is not distributed evenly over the load and it stops every time. you may need a repair man unless you can just move the dial to a drain spot rather than spin, if enough water gets out it will probably open then.

Ariston... | Answered on Jun 15, 2018 | 108 views

H2O is the symbol for WATER and probably indicates a WATER related fault on your machine. A pressure switch is the normal way the machines 'sense' when the level is sufficient. Overfilling suggests a faulty switch, which will need to be replaced by a technician. Also, ensure that the machine drains as it should, if not, the pump filter may be blocked.

Ariston... | Answered on Apr 04, 2018 | 440 views

the only thing to do is check that the water censor pipe is not blocked preventing the censor to tell the controller its finished the spin cycle this is a small 5mm pipe leading to wards the top of the machine take it off and blow gently down it you will hear a click and one when you release the air this means the censor is working but the small pipe where it came from is blocked clean the blockage with a pipe cleaner or similar replace the pipe eric

Ariston... | Answered on Dec 26, 2017 | 113 views

go online to

Ariston... | Answered on Dec 21, 2017 | 633 views

hmm sounds like a spring has busted inside your washer there and the diagnostic computer inside the washer was damaged so its not able to unlock its door....

Ariston... | Answered on Dec 17, 2017 | 169 views

Maybe get a knob type & eliminate this type of problems

Ariston... | Answered on Nov 22, 2017 | 645 views

Before you change fuses, do you have an internal fuse board or RCD system in your home? Sometimes, an individual RCD can trip out, locking off sockets. Some sockets are individually set up for up and downstairs in a house, or different rooms. If you have a board or RCDs, check them out :)

Ariston... | Answered on Nov 18, 2017 | 77 views

if it looks like a big yellow rubber band, it will stretch to fit
being rubber if you heat it up by repeated quick stretching it will be easier to assemble

Ariston... | Answered on Oct 25, 2017 | 195 views

This is normal , it takes small quantity of water unlikes old washing machines

Ariston... | Answered on Oct 04, 2017 | 56 views

Check the screen and the inlet to the pump in the bottom of the washer if it does not empty the water from the wash cycle completely it may not go to the rinse cycle.

Ariston... | Answered on Sep 06, 2017 | 98 views

I'm only guessing here but it's possible the internal thermostat is broken and the oven is overheating {?} and triggering some built in safety switch that turns the oven off so it won't cause any damage.
I suggest you call the company, or a local oven repair person.
Letting us know if it is Gas or Electric may help too.

Ariston... | Answered on Aug 01, 2017 | 95 views

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Ariston Technologies Experts


Level 3 Expert

85239 Answers

Tom Chichester

Level 3 Expert

57436 Answers

Bill Boyd

Level 3 Expert

53816 Answers

Are you an Ariston Technologies Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides