Ariston Technologies Logo

Ariston Technologies Popular Questions, Answers, Tips & Manuals

Do you work here? Claim your company

  • 31 Products
  • 1K Answers
  • 83K Views

did you check breaker in breaker panel

Ariston... | 56 views | 1 helpful votes


Pump fault or more likely blocked filter try cleaning should reset it self

Ariston... | 4,132 views | 0 helpful votes


H2O is the symbol for WATER and probably indicates a WATER related fault on your machine. A pressure switch is the normal way the machines 'sense' when the level is sufficient. Overfilling suggests a faulty switch, which will need to be replaced by a technician. Also, ensure that the machine drains as it should, if not, the pump filter may be blocked.

Ariston... | 441 views | 0 helpful votes


go online to https://www.manualslib.com/manual/645321/Ariston-Built-In-Oven.html

Ariston... | 636 views | 0 helpful votes


when I wash heavy stuff it will not spin properly because the weight is not distributed evenly over the load and it stops every time. you may need a repair man unless you can just move the dial to a drain spot rather than spin, if enough water gets out it will probably open then.

Ariston... | 108 views | 0 helpful votes


Maybe get a knob type & eliminate this type of problems

Ariston... | 646 views | 0 helpful votes


hmm sounds like a spring has busted inside your washer there and the diagnostic computer inside the washer was damaged so its not able to unlock its door....

Ariston... | 171 views | 0 helpful votes


the only thing to do is check that the water censor pipe is not blocked preventing the censor to tell the controller its finished the spin cycle this is a small 5mm pipe leading to wards the top of the machine take it off and blow gently down it you will hear a click and one when you release the air this means the censor is working but the small pipe where it came from is blocked clean the blockage with a pipe cleaner or similar replace the pipe eric

Ariston... | 114 views | 0 helpful votes


if it looks like a big yellow rubber band, it will stretch to fit
being rubber if you heat it up by repeated quick stretching it will be easier to assemble

Ariston... | 195 views | 0 helpful votes


Before you change fuses, do you have an internal fuse board or RCD system in your home? Sometimes, an individual RCD can trip out, locking off sockets. Some sockets are individually set up for up and downstairs in a house, or different rooms. If you have a board or RCDs, check them out :)

Ariston... | 77 views | 0 helpful votes


Check the screen and the inlet to the pump in the bottom of the washer if it does not empty the water from the wash cycle completely it may not go to the rinse cycle.

Ariston... | 99 views | 0 helpful votes


The most common failure in any electric oven is the heating element.

Ariston... | 847 views | 0 helpful votes


This is normal , it takes small quantity of water unlikes old washing machines

Ariston... | 56 views | 0 helpful votes


Sounds like the washer control panel has failed.

Ariston... | 154 views | 0 helpful votes


I'm only guessing here but it's possible the internal thermostat is broken and the oven is overheating {?} and triggering some built in safety switch that turns the oven off so it won't cause any damage.
I suggest you call the company, or a local oven repair person.
Letting us know if it is Gas or Electric may help too.

Ariston... | 95 views | 0 helpful votes


Tia The above answer would be helpful but I’m trying to get my dishwasher to drain & this makes the dishwasher do some type of cycle & doesn’t drain at all... pls advise

Ariston... | 231 views | 0 helpful votes


Washer fills with water and overflows:

The water pressure level switch is a pressure activated switch that is used to determine the correct water level in the tub. This part is normally located behind the control panel and will have a hose or air dome tube that connects it to the tub. On washers that use an electronic control, this switch may be located at the sump area below the tub. As the water fills in the tub it will compress the air in the tube and push against a diaphragm inside the switch. The switch will control the water inlet valve and turn the valve off at the correct water level. If the tube has a leak, not enough pressure may be created to activate the switch and the washer may overfill. If the switch is defective it may also cause the machine to overfill. To determine if the switch is bad, you should first eliminate the air dome hose as a problem. Look for signs of cracks or worn areas on the hose. Remove the hose and submerge in water. Seal one end and blow air into the other end and look for bubbles. Check for an obstruction in the hose as well. If the air dome hose appears to be ok, then the water level switch may be defective.

You can test it with a meter and with a manual test? ( first locate it in the panel, it has a plastic clear tube hose going into it, remove that tube from its connection, now put another small tube or hose into the slot where it was and have the machine set to wash cycle with water in it. Blow into the other end of the tube.
If the machine starts to wash. the pressure switch is more than likely good
( No wash- then THE DIAPHRAGM IS BAD AND SWITCH HAS TO BE REPLACED).

The other item to check would be your water inlet valve. Check it for continuity with a multi meter it should show Ohms or a closed circuit. To test it when water is overflowing unplug the unit and see if it still overflows or continues to fill. If it stops when unplugged. Then it is not a water inlet problem but an electrical signal problem going to ur water inlet valve. Possibly from the panel or board. You can also do a live volt test to see if it is getting the full 120 current, but be sure to unplug unit before testing as this is a live test.
Also another trick to check the water valve, is to first cut the water off and remove the hoses off the back of the washer. Then one at a time point the hoses inside the washer tub and turn the water back on. If you don't have good water pressure, turn the water back off and remove the strainer that should be in one end of the hose. Inspect the strainer to see if it is stopped up, clean it and reinstall it. Now repeat this test. If you have good water pressure now, reinstall hose and your problem is fixed

By the way my advice is free cuz God is good!




Ariston... | 37 views | 0 helpful votes


If you wish to get some details; check the site linked here. Pull up older posts.
http://electro-medical.blogspot.com/

Ariston... | 57 views | 0 helpful votes


I am supposing you are wanting a drive belt for your machine. Please type in "Ariston" on your search engine, as I did, and you will find that you can call them for your answers to your problems.
After a little looking, I found them in about 4 minutes.
God bless your efforts.

Ariston... | 43 views | 0 helpful votes

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Ariston Technologies Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Tom Chichester

Level 3 Expert

58394 Answers

Bill Boyd

Level 3 Expert

53816 Answers

Are you an Ariston Technologies Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...