Did the fluch mounts come with a resistor?
With a multimeter, check the resistance (Ohms) between the original blinkers and the new ones. You may need to add a resistor to make them the same so that they blink.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
The high mount brake light gets its own signal from the brake light switch (on the brake pedal). Or at least the wire leaving the brake light switch will splice, one wire to the high mount brake light, and the other for the rear brake lights is routed through the turn signal switch, and coordinated there with the turn signal wires to the rear brake lights. The brake wires and turn signal wires share the same wire, and same filament in the bulbs. It is kind of complicated, but brakes applied with no turn signal, brake light wire goes from brake light switch through the turn switch and out to the bulbs. If brakes applied with turning signal, non blinking brake light wire goes from turn switch to rear light, while the turning signal wire will go through the flasher relay, and then to the rear light to cause blinking.
I hope that makes sense. It appears the problem may be in the turn signal switch for both the turn signals and the rear brake lights.
These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. Surf the site with patience. If blinks continue without any pause, the main board is faulty.
These blinks [flashes] are fault indication. You can get an idea about the faulty stage circuit inside the TV, by the number of these blinks. Count it carefully, by switching it ON and OFF, more than 2 times at least, so that, you can make sure about the number of these blinks. If you wish to get more details, check the site linked here. Surf the site in "MOSAIC" view. http://electronicshelponline.blogspot.com/
Failed ground wire, no doubt caused by corrosion. Check under the vehicle at the rear or in the flasher bulb areas. Your main rear lighting common earth wire is the culprit. If you cannot find the corroded wire, then go to any rear bulb and attach a grounding wire from the bulb ground to the chassis. This will 'repair' the other missing ground feeds. The indicator is being grounded through the other bulbs circuits, rather than to vehicle chassis. You need to locate a circuit schematic and check the ground point locations. It could be anywhere unfortunately, so adding a new ground wire is the alternative grounding replacement method.
the front one that doesnt work , must have a bulb gone or wire off. The reason the rear doesnt blink is it needs the power flowing through both bulbs for the flasher to work. You may need a test light to check for power going to the front
Hello!
When was the last time you replace lamp in your TV? If long time ago (2+ years) - replace the lamp.
If red light blinks in sequence (example 4 flashes, pause, 4 flushes, pause and so on) - then I need to know how many flushes between pauses. It is an error code. If it blinks just constantly - it is a bad lamp.
Regards.
Russ.
Hi, Power light blink 3 times shows that convergence out ICs got defective and need to be replaced. If you are handy with electronics stuff repair and can solder parts in circuit board with proper tools then replace two big black ICs, convergence out, mounted on aluminum heat sink. Or call local tech to fix it. Let me know if you have additional question. Thanks.
there will be a black cap with a red hose attached to it you have to buy the fitting if you dont have one it should be located in rear compartment mounted on the wall you will have to pull the tray out sometimes they mount them under your dry box in the front but most of the time they be in the back
×