What is the split pump - Heating & Cooling

PDF]4HP13/14 SPLIT SYSTEM HEAT PUMP - Armstrong Air

www.armstrongair.com/_/.../Armstrong_4HP13L_Install_506318-01.pdf

4HP13/14 SPLIT SYSTEM HEAT PUMP .... indoor unit, outdoor unit contains system refrigerant charge for operation ... may be installed with up to 50 feet of line set (no more than ..... The defrost control incorporates 2 pressure switch .... Note: Sensor resistance decreases as sensed temperature increases. Pins/Wire. Color.Missing: tempstar

[PDF]RESIDENTIAL SPLIT HEAT PUMP SYSTEMS

icpindexing.toddsit.com/documents/086477/42808100101.pdf

This Manual Supports Split Heat Pump Units of The Above Series .... two groups is based on a difference in Defrost controls and/or the .... completes a circuit between µRµ ? µOµ in the the thermostat sub-base. 2. .... before connecting line voltage. ...Wire "S1" is the first stage of electric heat through the outdoor thermostat.

[PDF]Trane Installer's Guide Air Conditioner/Heat Pump 4TTZ0 ...

3 Ton Heat Pump Split System ' eBay

www.ebay.com/bhp/3-ton-heat-pump-split-system
eBayGoodman 3 Ton 14 SEER Heat Pump Split System GSZ140361 with Installation Kit.10k Heat Strip,Thermostat,Wiring, Disconnect Box,Pad. $1,912.00; Buy It ...

410 a runs at a much higher pressure then r-22. that is still very high. it would take a temperture over 150 degrees to produce it on a idle system.

I believe the wiring may be incorrect. Here arethe fault codes.

05

Comms Error, check your wiring, remove external pumps. Split/Multi - check volts from terminal N to 3 = 0 - 65 Vdc, Multi V - 4 Vdc terminals 3 and 4

5

Comms Error, check your wiring, remove external pumps. Split/Multi - check volts from terminal N to 3 = 0 - 65 Vdc, Multi V - 4 Vdc terminals 3 and 4
Hope this helps

Bob

Indoor unit faults = CH04 or C4
Fascia LED's
- RED = None
- GREEN = 4 Flash
Contents = Drain Pump / Float Switch
Case of Error = Float Switch Open Circuit (High Level Water Alarm)
Indoor Status = Off

clean your condensate drain line you can do this with a shop vac,
Read more: http://dgoma.es/multisplit_lg/lg-multi-split-units-error-code/#ixzz34dr3Cu00
Follow us: dgoma on Facebook

No question, hope you got it split, new gasket in and back together.

Sounds like you have an air leak. First check your fittings, next carefully run water over the pump seals (avoid getting water on the motor or you'll hurt yourself and the pump if not worse) the pump will prime if the leaking seal is covered with water. Take your time and be careful and it should only be a matter of a loose fitting or simple seal swap.

a split system can be gas or can be a heatpump. a split system is when the condenser coil compressor and outdoor fan is outside. the other half is in the house close to your air filter .that well be your air handler. eletric heater. or gas burner .and indoor fan motor would be. i hope that helps you.

Hi there Luke. The sprocket gear of the pump is sitting on a taper lock on the pump shaft, you have to use a puller to get it off the shaft. Mount the puller to the threaded holes on the sprocket and when it is tight, give it a sharp crack with a hammer, it will then pop off.
Caution!!!!! Do not hit to hard the pump shaft has a transfer pump attached inside that is quite sensitive.
Before you do drastic things like removing the pump please read the attached manual on setting the timing, special tools are needed to reset the timing.