20 Most Recent Hifonics BX1000D Car Audio Amplifier - Page 4 Questions & Answers

you may have damaged your amp internally... servicing may be required, however try leaving no power to it overnight and try in the morning. Good luck

no sound on my mid speakers help 1998 740i bmw

++++wow, that's harsh
, did anything spill from the bottle?
?
or was it just the impact?

Try reversed the connection, hang the positive supply together with the ground. Then connect the ground first before the positive supply. If the spark is still there then you are confirmed that you have a short on the unit. Fixing is not DIY because it is quite technical. I rather suggest to send it to a repair shop to isolate the shorted parts. A series of test will be perform to locate where the short come from.
Please rate my advice.
Thanks for using fixya...

Short answer: NOPE!

The Hifonics Brutus 2100 is stated to produce 2100 watts RMS @ 1ohm load. Most amplifier manufacturers overstate their claims. The 2100 watt output is most likely at 14.4 volts and not the 12.6 volts your car will actually be providing the amp.

But, even if the actual output was 2100 watts that would be 1050 watts to each 12w7. The 12w7's are rated at 1000watts RMS and 2000watts peak. As a MECP certified installer, any system I have done using 12w7's have had a MINIMUM of 1000 watts being provided to each speaker. My personal preference is to run 1500 watts each and keep the gains adjusted lower on the amp. Thus allowing the amp to run cooler and allow the additional headroom for those "show-off" moments!

closest i can get you to a schem is ampguts.com

Chances are you have your woofers wired in parallel i would rewire your speakers in series and that should solve all your problems.

check the power supply board .any of the components on the power supply board is got loose and the circuit is not getting completed so the power is not coming on.
get the components checked with the meter and continuity tester.replace the faulty.you can get replacement component from electric hardware shop.
This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

is it for the power or the sub

Depends if its bridgeagle or bridge internally. bridgeing provides the most power to a mono system. 2 positives and 2 negative you have a 2 channel amp. Heres a link to check out, you should be able to figure out your system and hook it up with this. Hope it helps. http://www.wikihow.com/Bridge-an-Amplifier

clipping can result from improper wiring or solder jumps to figure this out youll need a continuity tester simply check you inputs and outputs and make sure wiring is correct then if so your amp has a solder jump inside them amp. New amp or send it in for repair you can buy a new amp nearly every brand at dealer cost from this site.
www.godspeedaudioheaven.com

try  www.bestbuy.com or radioshack.com to get the required parts.

Possibly you need to return the amp and get a new one cause that could mean an internal problem and its deffective, you could try replacing the fuses or try changing the ground wire, this problem is very unusual

Hey there,

I'm assuming you want specs on all Hifonics Speakers and Subs. No Problem.

Click the following link:

Hifonics

From there you can get info/specs on all their products.

Cool site.

Hope this helps

Mike

The radio code is a security feature that's meant to deter theft, and it's unique to each vehicle. If you've lost your code, you'll need to contact a Nissan dealership or service center and provide proof of ownership. They should be able to help you retrieve the code. Please do not attempt to use codes from the internet as incorrect attempts may lock your radio.

How to change language to english for Honda Odyssey 2021 Gathers Radio Player

I have the same radio now with no Bluetooth am trying to get Bluetooth on it too without having to buy another radio. Please help.

First thing to do is check to make sure that the batteries are properly charged.

Second, make sure that you have a clear line-of-site to the IR transmitter. Infrared (IR) works the same way that your TVs remote control works - if the signal is blocked, then you will not hear any sound.

Third, make sure that you are in the rear seat of the vehicle when listening to the sound. The IR transmitter only transmits to the rear seat, so you will not hear any sound if you are sitting in the front seats. This is a common problem that i see.

Lastly, make sure that the heapdhones you purchased are compatible with your 2006 2007 2008 2009 or 2010 Toyota Sienna. Remember that some older models require RF headphones, not IR headphones. I checked http://www.audiovideo2go.com for compatibility before I purchased my headphones. They have a useful listing of all the headphones and models of vehicles they are compatible with.

'make model (what is is)' as first 3 words in all questions. https://www.google.com/search?q=demo+mode+the+code+for+4.91 ..

Unfortunately, no one knows or is telling. Companies rarely state power in RMS because Peak Power is a much more impressive. 1000 watt amp, 200 watts RMS x 2 channels at 8 ohms. Look for a sticker on the unit. https://www.google.com/search?q=Xplore+Amp+5553 ..