Car Audio & Video - Recent Questions, Troubleshooting & Support
Sony CDX-M850mp isnt playing any audio from aux or cd input
This issue might be due to a malfunctioning auxiliary input or a problem with the amplifier circuit. You can try the following steps to troubleshoot the issue:
- Check the connection between the auxiliary input and the head unit to make sure it's properly plugged in.
- Check the audio cable for any signs of damage or wear.
- Make sure the auxiliary input is selected as the source on the head unit.
- Check the amplifier circuit to see if it's functioning properly. If it's not, the amplifier may need to be repaired or replaced.
If these steps don't resolve the issue, it's recommended to have the unit inspected by a professional audio technician.
Sparkomatic S8E7 Compact Equalizer Booster Install manual
To connect the Sparkomatic equalizer to your Kenwood head unit, follow these steps:
- Connect the RCA cables from the head unit's preamp outputs to the equalizer's inputs.
- Connect the RCA cables from the equalizer's outputs to the amplifier's inputs.
- Connect the equalizer's power and ground wires to the amplifier's power and ground wires.
- Turn on the head unit and equalizer, adjust the equalizer's settings as desired and enjoy improved sound quality.
Note: If your head unit does not have preamp outputs, you may need a line output converter or signal processor to connect the equalizer.
1998 Mercedes Benz ML320. Any ideas on what is wrong with my Mercedes please?
It sounds like you're experiencing a transmission issue with your 1998 Mercedes Benz ML320. If the transfer case motor replacement didn't resolve the issue, here are a few other troubleshooting steps you can try:
- Check for codes: Use an OBD-II scanner to check for any trouble codes stored in the vehicle's computer. This may give you a better idea of what's causing the problem.
- Check the transmission fluid level: If the fluid level is low, it could be causing issues with the transmission.
- Check the transmission filter: The filter could be clogged, which could be causing the transmission to shift erratically.
- Check the transmission control module: This module could be faulty, which would cause issues with the transmission.
- Check the throttle position sensor: This sensor could be faulty, causing the engine to misbehave.
It's important to keep in mind that troubleshooting a transmission issue can be complex, and it's best to seek help from a professional if you're not familiar with the inner workings of a transmission. If you're comfortable with working on cars, you can research the specific issue you're experiencing and try to find a solution online, but be cautious and make sure to follow proper safety procedures.
I have a kenwood head unit with 12 pin for a cd changer, I have connected a kenwood cd changer when I press the cd changer source on my head unit it's coming up aux ext but no changer options
It sounds like you're having trouble connecting your Kenwood CD changer to your head unit. Here are a few troubleshooting steps you can try to resolve the issue:
- Check the connections: Ensure that all the wiring connections are secure and properly connected to the head unit and CD changer.
- Reset the head unit: Disconnect the power to the head unit, wait a few minutes, and then reconnect it to see if the issue is resolved.
- Check the compatibility: Make sure that the CD changer you have connected is compatible with your head unit and the 12 pin interface.
- Update software: If your head unit has firmware or software updates available, it may be worth updating to see if the issue is resolved.
- Contact the manufacturer: If the above steps do not resolve the issue, it may be best to contact Kenwood's technical support for further assistance.
It's important to handle the head unit and CD changer carefully to avoid causing further damage or issues. If you are not familiar with the installation and connectivity of a CD changer, it may be best to seek help from a professional for a repair.
Kenwood A58 amplifier spectrum issue
It sounds like your Kenwood A58 amplifier may be having a technical issue that could be caused by several factors, including an internal component failure, a wiring problem, or a software issue. Here are a few suggestions to help resolve the issue:
- Check the wiring: Make sure that all the wiring and connections to the amplifier are secure and properly connected.
- Power reset: Disconnect the power to the amplifier, wait a few minutes, and then reconnect it to see if the issue is resolved.
- Update software: If your amplifier has firmware or software updates available, it may be worth updating to see if the issue is resolved.
- Contact the manufacturer: If the above steps do not resolve the issue, it may be best to contact Kenwood's technical support for further assistance.
It's important to handle the amplifier carefully to avoid causing further damage or issues. If you are not familiar with the internal workings of an amplifier, it may be best to seek help from a professional for a repair.
Manual for volfenhag zx 7190
The manual for the Volfenhag ZX 7190 amplifier will provide the specific instructions for connecting the amp to your system. Here are some general steps for connecting a car amplifier:
- Connect the power cable: Run the power cable from the battery to the amp, making sure that it is securely connected.
- Ground the amplifier: Connect the ground wire from the amp to a metal surface in the vehicle, such as a bolt on the chassis.
- Connect the RCA cables: Run the RCA cables from the head unit or source device to the amp, and connect them to the input jacks on the amp.
- Connect the speaker wires: Run the speaker wires from the amp to the speakers, making sure to match the positive and negative connections.
- Turn on the amp: Turn on the amp by switching the power switch to the on position.
It's important to make sure that the amplifier is properly connected to avoid damaging the amp or your vehicle's electrical system. Additionally, you should also refer to the manual for your specific Volfenhag ZX 7190 amplifier, as the connection process may vary based on the model and features.
Pioneer xv-htd540 5 disc dvd/cd changer surround sound system TIMER LIGHT KEEPS ON BLINKING
The timer light constantly blinking on a Pioneer XV-HTD540 5 disc DVD/CD changer surround sound system could indicate a few different issues. To resolve this issue, you can try the following steps:
- Check the connections: Make sure that all cables are securely connected to the system, including the power cable, audio cables, and any other cables that may be required for your setup.
- Reset the system: Unplug the system from the power source, wait for a few seconds, and then plug it back in. This can sometimes resolve any issues that may be causing the timer light to blink.
- Check the discs: If you have any discs in the changer, remove them and try turning the system on without them. Sometimes, a dirty or damaged disc can cause the timer light to blink.
- Perform a factory reset: If the above steps do not resolve the issue, a factory reset of the Pioneer XV-HTD540 may be necessary. This will restore the unit to its original settings and resolve any software-related issues.
If these steps do not resolve the issue, you may need to seek further assistance from the manufacturer or a professional repair service. It's important to follow the manufacturer's instructions and safety guidelines when attempting to repair or troubleshoot your system to avoid damaging the unit or causing potential harm.
BEOSOUND9000 - When BEO4 is set to 'CD' 'Shift 90258' for test mode, when I then press '72' the message on the BEOSOUND 9000MkIII states 'Wrong SRC/TM' even though It worked at the start of the repair
The message "Wrong SRC/TM" on a BEOSOUND 9000MkIII when pressing '72' while in test mode (Shift 90258) and set to 'CD' could indicate that there is an issue with the source selection or the test mode itself. To resolve this issue, you can try the following steps:
- Check the source selection: Make sure that the correct source (CD) is selected on the BEO4 and that it is functioning properly.
- Check the test mode: Verify that the test mode has been activated correctly and that the Shift 90258 code has been entered correctly.
- Check for firmware updates: Make sure that the firmware on the BEOSOUND 9000MkIII is up-to-date. If there is a firmware update available, install it to resolve any issues with the test mode.
- Factory reset: If the above steps do not resolve the issue, a factory reset of the BEOSOUND 9000MkIII may be necessary. This will restore the unit to its original settings and resolve any software-related issues.
If these steps do not resolve the issue, you may need to seek further assistance from the manufacturer or a professional repair service. It's important to follow the manufacturer's instructions and safety guidelines when attempting to repair or troubleshoot your system to avoid damaging the unit or causing potential harm.
Wiring diagram for Panasonic cq-c1100 u
I'm sorry, but wiring diagrams for specific car audio systems are not readily available to the public. These diagrams are usually confidential and used by authorized repair technicians only. If you need assistance with the wiring of your Panasonic CQ-C1100U car audio system, I would recommend reaching out to the manufacturer or an authorized repair service for support. They should be able to provide you with the information and guidance you need to properly install and wire your system. It's important to follow the manufacturer's instructions and any relevant safety guidelines to avoid damage to the system or potential harm to yourself or others.
Lasko silent room heater Model Number 5628
I apologize, but wiring diagrams for specific home appliances are not readily available to the general public. These diagrams are usually confidential and used by authorized repair technicians only. If you need to repair or replace the cord on your Lasko silent room heater Model 5628, I would recommend reaching out to the manufacturer or an authorized repair service for assistance. They should be able to provide you with the information and support you need to safely and effectively repair or replace the cord.
No voltage on motor after replacing belt Tascam Midistudio 644
The issue with the voltage regulators getting hot and the motor not receiving any voltage after replacing the belt on your midi studio could be caused by several factors. To resolve this issue, you can try the following steps:
- Check the wiring: Make sure that all wiring connections are secure and that no wires have been damaged or disconnected during the belt replacement.
- Check the voltage regulators: The voltage regulators could be overheating due to a short circuit or incorrect voltage. If they are hot to the touch, disconnect the power immediately and replace them with new ones if needed.
- Check the motor wiring: The motor may not be receiving voltage because of a wiring issue. Make sure that the motor's wiring is connected securely and that the voltage is present at the motor's terminals.
- Check the power supply: The power supply may not be providing enough voltage to power the motor and voltage regulators. Make sure the power supply is functioning properly and providing the correct voltage.
If these steps do not resolve the issue, you may need to seek further assistance from the manufacturer or a professional repair service. It is important to handle electronic components carefully and to follow all relevant safety guidelines to avoid damage or injury.
1/29/2023 12:37:14 PM •
Tascam...
•
Answered
on Jan 29, 2023
Why not show CD track info on Kenwood c-h7 using dp-mh5 player? what error ? what should check?
The issue with not showing CD track information on your Kenwood C-H7 using the DP-MH5 player could be caused by several factors. To resolve this issue, you can check the following:
- Compatibility: Ensure that the DP-MH5 player is compatible with the Kenwood C-H7 unit.
- CD format: Ensure that the CD is in the correct format and meets the requirements for playback on the DP-MH5 player.
- CD read error: Make sure the CD is clean and free of scratches, as these can cause read errors that prevent track information from being displayed.
- Connections: Check the connections between the DP-MH5 player and the Kenwood C-H7 unit to make sure they are secure and properly connected.
- Software/firmware: Make sure that both the DP-MH5 player and Kenwood C-H7 unit have the latest software/firmware installed and are up to date.
If these steps do not resolve the issue, you may need to seek further assistance from the manufacturer or a professional repair service.
Been trying to hook up. Y performance teknique icbm-9707b can't seem to make it work it turns on then off it only makes a wishlsonose
I'm sorry to hear that you're having issues with your Y performance teknique ICBM-9707B. To help diagnose the problem, please provide the following information:
- What is the device supposed to do?
- What is the exact error message or behavior you are encountering?
- Have you tried troubleshooting steps, such as checking the power source or connecting cables?
- Is there any recent hardware or software changes made to the device or the environment it is used in?
Providing this information will help me better understand the issue and provide more specific advice to resolve it.
Not finding what you are looking for?
