20 Most Recent
RCA 32V420T 32" TV - Page 5 Questions & Answers
Rca tv fix
From the way you sound, you don't know what you are doing. This area of the set is fairly dangerous to mess with.
I would give the set to a qualified shop, or get a new set!
Jerry G.
Tv controls respond erraticaly
most of these rca models have bad flybacks. also check horz output transistor, if flyback is relaced the screen voltage has to be at or close to 295 volts or set will shut down after on 5 seconds
clintstv
Rca arcing and hissing
Most likely,you have a bad transformer AKA flyback ......
Is 32V420TYX6 the service # of your TV ?......Verify..........T.
32" RCA when plugged in snaps an arcs
Normally an arc or snap like that is coming from the anode cap that attaches to the top center of the crt. The voltage there is upwards of 25k so be VERY careful if you're going to inspect this for any faults. If it is the cap leaking unplug the set and take a piece of wire attached to a screw driver with the other end of the wire attached to the grounding cable around the outer edge of the crt. Gently undo the cap from the crt and allow the blade to sit in the well for a period of time to discharge the crt completely.
Next get some HV putty, sold at most electronics distributors like Mouser and form a small ring with it. Place it around the well hole in the crt and replace the anode cap pressing firmly to seal the edges of the cap to the crt. With the back still off plug the unit in and see if that's cured the problem.
Bill
32" rca picture stretched
Before you fool around with this, it may be under warranty. Check that first. Second, does the picture stretch in both directions or just vertically? If just vertically is it more pronounced at the top?
Thanks,
Dan
No picture or anything
If your model # is 32V420T, your TV probably has a bad
transformer = part # 271996............if not,please provide......T.
Power surge
DONT BUY RCA AGAIN
..NO SERIOUSLY..I'VE REPLACED THE FLYBACK TRANSFORMER AND H.O.T.
TRANSISTOR FOR MOST OF THESE PROBLEMS....NORMALLY A SURGE WILL TAKE OUT
THE POWER SUPPLY...IN WHICH CASE THE BRIDGE DOIDE WILL BE SHORTED AND
POSSIBLY THE TRANSFORMER....HOPE YOUR HELPED....MICHAEL SPARROW
RCA Home Theatre System 51 or 52"? Chassis # PTK169PAAS
If it is a "minor" convergence problem you can adjust it by going to the menu and scrolling to convergence and follow prompts A cross will appear when you have reached the correct place and you do the minor adjustments as it says. If picture is bowed you have major convergence problems.
Help
hi there, you have parts to be replaced. it is not worth to fix it. the cost of the parts is almost the same as the new one. ty
RCA F27442 27" TV
1) Ask what the part location on the board is = IC301 for example..
2) Provide service #
3) Could be LA7612N
4) If they were not blowing smoke,why didn't they give you a
six digit RCA part # ??
....................................................T.
Channels
Provided you have signal above 23.......
Usually in set-up menu there is a cable / normal selection of some sort to be selected before activating auto-program....T.
Let me know.......
Hdtv?
is not a hdtv , and its 4x3 aspect ratio
Powers off by itself
Usually leaky power supply diode and two bad caps-----need service # and chassis # from
sticker on back of set .....T.
Turning on and off
Perform reset procedure by unplugging AC cord
for a few minutes,then an hour,then overnight,
if need be.
RCA 32V432T
FIRST THING TO TRY IS RESET-unplug AC cord for
a few minutes,hours or overnight==let me know
if you need more help.T.
52" RCA menu
1)Please clarify model #
2)Try reset==unplug AC cord for a few minutes,
a few hours or overnight,if need be.
3)let me know if you need more help.T.
RCA 32V420T 32" TV
reset by unplugging AC cord for few minutes,
a few hours,or overnight,if needed.Let me
know if that does not work.T.
Not finding what you are looking for?