20 Most Recent
Epson DFX 8000 Matrix Printer Questions & Answers
I am trying to get
Sometimes just unplugging printer from outlet will clear any software issues. Not from the PC but from power outlet. Leave unplugged for about 30 seconds.
Alpha seting of dfx 8000 printer
The purpose of this adjustment is to set the PG offset value in accordance with the nose dimension
of the printhead. (For details, refer to Chapter 2.)
The offset for the nose dimension is represented by the adjustment value “ALPHA.” The “ALPHA” value
is stored in the memory on the main board, so the PG adjustment mechanism can read the value as
needed. Be sure to perform the adjustment when required. If this adjustment is not performed correctly,
the platen gap will be incorrect, the paper could be caught by a head pin, or, in the worst case, a head
pin could break.
NOTE: The printhead adjustment value is written on the front of the head unit (refer to Figure 4-2). After
the printhead is attached, the value cannot be seen. Be sure to write down the value before
attaching the printhead.
Step 1: Connect the AC cable. Mount the ribbon cassette, and load paper into the front tractor.
Step 2: Turn the printer power on while pressing the LINE FEED, MICRO FEED (V), and PAPER SELECT
switches (Be sure that the top cover is closed. Do not open it until you turn the printer power
off.), then wait until the buzzer rings five times.
REV.-A
Step 3:
Step 4:
Step 5:
Step 6:
Load the paper by pressing either the LINE FEED or PAPER SELECT switch, then wait until
the PAPER OUT lamp goes off (approximately 15 seconds).
(
Press the ON LINE switch.
Press the MICRO FEED (A) switch the number of times indicated by the value written on the
front of the printhead.
l The buzzer rings each time the MICRO FEED switch is pressed.
l Press the MICRO FEED (A) switch to increment the value.
l Press the MICRO FEED (V) switch to decrement the value.
l The value range is O to 10.
To confirm the value stored, press the FORM FEED switch so that the value is printed.
l If the value is incorrect, return to Step 5.
. When the value is correct, go to Step 7.
Step 7: Press the ON LINE switch and confirm that the buzzer rings five times. The printer prints the
final value stored. If the value is correct, turn the printer power off.
Prints one side faded
Epson Dot matrix DFX 8000
Due to printer head firing is not proper.
The Prnter need servicing and once serviced it will be alright.
Sometimes the Printer Ribbon might have not rotating and the print will not be visible on the left and at right side it is bright.
Better consult the local printer hardware enigneer and settle this iseeu.
Put the original and best gsm paper in the printer, when prining job is iniated.
Dfx 9000 error 07" Questions what is the possible solution
The service manual says it is a voltage related problem within the unit. After time parts wear an over heat. You either have a voltage supply board that has problems or the ROM board has a bad componet on it. Many times they can be repaired with a recap job. Sometimes its better to replace the board. If you are not a tech person take it in for repair or get another printer.
Dfx 8500 shuts down with error code 06
Update the printer drivers also fix windows internal errors by scanning PC with an updated Anti-virus.If problem still exists then after scanning with anti-virus, scan pc with a reliable registry cleaner tool like PCFresher for an instant fix.
Epson lq-690II printer reflects the paper when printing
Troubleshooting Paper Reversal in Printers:
*Confirm that options related to paper handling are set correctly by checking for specific buttons or switches that relate to paper handling or reversing.
*Ensure that paper is loaded properly to avoid feeding problems.
*Remove any dust, particles, or paper remnants from the rollers, as they can impede paper flow.
*If other measures fail, reset the printer to its initial settings to resolve potential software glitches.
EPSON 15140 error 034019
Try a hard reset of the printer. Oddly, the 034019 is not an error code, I have reason to think. It is a contact number, I believe.
Reset my Epson printer L382
Follow the steps given below to reset Epson L382 printer.
Step 1: Turn the printer off.
Step 2: Press and hold the reset button which is on the back of the printer using a paper clip or tip of a pen.
Step 3: Turn on the printer by holding the Power & reset button and continue to hold both the buttons.
Step 4: Wait for 5 seconds and a warning sheet will print. Release the reset button.
Step 5: After 5 seconds, another sheet will print which will show the IP address of the printer.
hold the reset button which is on the back of the printer using a paper clip or tip of a pen.
WHERE IS RESET BUTON? I CANT FIND IT.
I have Epson printer workforce pro c5790 shows error 000101, what is the solution for it ?
The error code 000101 on an Epson Workforce Pro C5790 printer typically indicates a problem with the print head.
Here are some steps you can try to troubleshoot and fix the issue:
- Perform a print head cleaning: From the printer's control panel, navigate to the Maintenance menu and select the option to perform a print head cleaning. This will help to clear any clogged nozzles or debris that may be causing the error.
- Perform a print head alignment: From the printer's control panel, navigate to the Maintenance menu and select the option to perform a print head alignment. This will help to ensure that the print head is properly aligned and is able to print correctly.
- Check for any physical obstructions or debris in the print head area, if you find any, remove it carefully.
- If the error persists after trying the above steps, you may need to replace the print head.
- If none of the above steps work, it is possible that the printer has a more serious problem that requires professional service.
I recommend you to check the user manual or contact Epson technical support for further assistance and specific troubleshooting steps for your printer.
Not finding what you are looking for?