20 Most Recent E-Machines eMachines T3830 PC Desktop - Page 5 Questions & Answers

You would need a multimeter to check for a faulty switch, they are cheap you can pick up an $8-$10 one at just about any hardware store

Look very closely at the motherboard where the wires go... maybe with a magnifying glass . should say what wires go where. ie. (hdd led,reset, pwr. etc) if you reverse the wires.. just switch them back. its just for indicators.. also u could google the mainboard model number or search acer site for led pinout on mainboard.

You have a virus or some bad malware. If you have an antivirus or spyware program run it. If you dont you have a problem because it will block every attempt to fix it on line.

Make sure you are placing the CDs in the drive with the label side up. If the computer can read DVDs, it can certainly read CDs as well. Once the cd is inserted, wait and the autoplay should start the installation program for the software.

You say that you pressed all the fx keys and delete key. Were you trying to get into the BIOS setup? If the keyboard is frozen no amopunt of key combinations will work. You might have to reset the BIOS to default settings. That means connecting a couple of pins together for a short time on the motherboard. You may need the manual if you don't already know what pins. Just make sure the power is completely of and the mains cord is pulled out.
It can vary the amount of time required to reset but if the corrupted BIOS was not caused by an overclocking it should be instant.
Once it is reset put the pins connector back the way it was. You may then want to go into BIOS setup, to set things up again to your preferences or needs. Again depending on your knowledge have the manual with you.

you can try to contact facebook and explain the issue with them, just ask them if they can reset your email because you don't have acess to the old email so you can reset your password

you can use mozilla fire fox browser also but for permanenet solution for this error you can repair your windows operating system or try by running chksak command in run window.

just uninstall then reboot then re-install yahoo messenger but this time install the latest version.

Same old same

If you have the powerpoint or microsoft office disk

Uninstall and reinstall with your cd key...

Hi
You can download the toolbar from the following website
http://www.brothersoft.com/ultimate-youtube-toolbar-86249.html



Thanks for using Fixya
proton

The screen could not have shifted only for one game or prog. It may be larger on all side and you notice it during the game when you want to access the buttons. So, press the settings button and reduce the screen size to occupy the whole physical screen (ie, max and no more). Now you will get the whole picture on the entire screen.

before you plug in your printer to the usb port you should install the printer driver first then plug it in!Now your printer will find the driver!!

Hello.

There is a hidden Administrator account that is created when your operating system is installed. Access that account and then reset your password.

1. Boot your computer and press F8 repeatedly
2. Access Safe Mode
3. Key in “Administrator” in Username, with no password.
4. Go to Control Panel, then User Accounts
5. Select the account you want to reset the password
6. Change the password

Hope this helps

possibly check the power supply, might need to be replaced

look on the back of the computer you will see all your connections there.

eMachines T3642 Computer takes the PC2-5300 DDR2 SDRAM DIMMs. Supports Dual Channel DDR2. Memory Type, and comes installed with 1.0 GB = 512 MB (removable) + 512 MB (removable) of Memory. You can upgrade your eMachines eMachines T3642 Computer to up to a maximum of 2.0 GB Memory, the system has 2 sockets to install Memory, already with 1.0 GB = 512 MB (removable) + 512 MB (removable) standard Memory installed. For best Computer performance use the maximum amount of allowed Memory per slot for your Computer.


INSTALLATION PROCEDURE
1. Place the computer power switch in the "off " position and disconnect the AC power cord.
2. Remove the computer top cover following the instructions in the model-specific owner manual.
3. Before touching any electronic components, make sure you first touch an unpainted, grounded metal object to discharge any static electricity stored on your clothing or body.
4. Locate the memory expansion sockets on the computer motherboard. If all the sockets are full, remove smaller capacity modules to allow room for higher capacity modules.
5. The ejector tabs shown in the illustration are used to remove a module. By pushing outward on the ejector tabs, the module will pop-up from the socket and it can then be removed.
6. Handle your new module carefully; do not flex or bend the module. Always grasp the module by its edges.
7. For most installations, DDR modules can be installed in any available expansion slot. Other installations may require the memory to be installed in a particular sequence based on the modules capacity. Check your owner manual to determine the correct installation sequence for your configuration.

Insert the module into an available expansion socket. Note how the module is keyed to the socket. This ensures the module can be plugged into the socket one way only. Firmly press the module into position, making certain the module is completely seated in the socket. The ejector tabs at each end of the socket will automatically snap into the locked position. Repeat this procedure for any additional modules you are installing. 8. Once the module or modules have been installed, the computer top cover can be reinstalled.
9. Plug in the AC power cord and reinstall any cables disconnected during the installation process.
10. Turn on the computer and follow the instructions in your computer owner manual that describe the steps necessary to allow your computer to recognize the newly installed memory.

I’m happy to help further over the phone at https://www.6ya.com/expert/william_83fc156eee2b555e

mouse and keyboard are color (purple and green) coded monitor is serial port only fits on one place and screws on! Power plug is at top has three slots in cord! It hard to plug things in wrong! plug um all in and turn it on!!

The best way to fix this is to right click in the corner where you used to access the toolbar. You will see choices, just left click on one of them to enable or check it. Once you click the right one you will see the minimize, restore and X to close buttons reappear

it is better if u try to boot ur system by a dos bootable disk (floopy or cd) then run Fdisk and re partiioned ur disk and format .

best of luck

depends on your operating system and bios i think.
you cant do it any harm...honest...just press f6 or f8 i think as it boots and a screen will show up asking what you want to do next?....read the screen and follow the intructions as there can be a few choices to go for.if you dont get the screen just SOFT restart untill you find the f-key that brings up the boot menu by pressing together CTR,ALT & DELETE at the same time to re-boot and then hold down another choice of f-key untill you hit the boot menu...hope this helps :)