Top 20 D-Link DAP-1522 Xtreme N Duo Wireless Bridge/Access Point (DAP-1522/B) Pre-802.11n - Page 3 Questions & Answers

do you have a good internet connection?

Hi! this is Alex Walker expert to help you for this issue call me on +1(518)348-9393 I will be glad to assist you Thank You

Hello VAMM I can help you in that case but you need to explain more. So whenever you have time just call on +1 (833) 493-0111 (toll-free) number.Cheers,John

Try an external usb wi fi adapter and see if that works - if so, then your initial diagnosis is correct.

I attempted to use D-link equipment TWICE in the past... I went as far as wasting a net of 3 hours each time with their "TECHNICAL" support... OVER & over... to the definition of insanity... Had anything worked I would tell you ABOUT IT. I would strongly recommend you return them from WHERE-EVER you purchased them... NOW. My next was a single unit NETGEAR... Cost less and I had cable connected my video server WIRELESSLY... in a matter of minutes. My OPINION: Avoid the pain. Carnac the Magnificent

go to dos prompt in a windows pc and type in ipconfig and press the enter key to find the default gateway address it might be 10.0.0.1 or 192.168.0.1 these are the most common. Type the ip address into internet browser to log into the gateway router. There will be an admin user name and admin password. It might be the default or it might be written hopefully on the router case/ try Username: cusadmin Password: password IP Address: 192.168.0.1 http://www.cleancss.com/router-default/SMC/SMC8014WG if you get into it look up wi fi security to find out the wep key or wpa key

Can you access msn.com via command prompt?

Hi, Check the link below ftp://support.dlink.co.in/pdfs/products/DSL-1504G/DSL-1504G_ds.pdf

run the command getmac on cmd and you will get the mac address of mac address of computer skype id :[email protected]

Our technical expert solves more than 500+ issue every day. we are available in every unapproachable location of USA/Canada. The customer can contact us any time, our technical staff always ready to solve your all issue. Therefore if you are facing any kind of issue which is mention above so don't need to worry about it just Dial our Toll-free Number D-Link Support Number USA 1-833-284-3444. https://servicenumber.org/d-link.html

Not all antenna are removable, if it does not easily unscrew, it is probably not removable.

https://youtu.be/Mop2Hrlj6_o here is a youtube video about this hope this works!

ISP providers purposefully slow down your data. Its been a real fight to get the FCC and Congress to address this. Other than that, I suggest using you WAN. Only use cabled connections because they are much faster than the best radio.

The speed of your internet is determined by your service provider and their modem. If possible, connect directly to the modem to check the speed. If you suspect you D-Link router is not allowing you to get full internet speed, first a Hard Reboot of you Router and Modem. If that did not solve the issue, try a known working LAN 5e cable between your modem and router. After you have established it is not a cable issue, do a factory reset. I had an issue where my speed to the internet modem was fine, but the router LAN connections only provide a faction of the internet speed. After testing cables, etc I did a factory reset and it restored full connection speed on my router LAN ports.

If using lan just connect the extender to the router with a lan cable. The extender will no need to setup.

http://www.dlink.com/uk/en/support/faq/routers/mydlink-routers/dir-810l/how-do-i-change-the-wifi-password-on-my-router Instructions at above link

Try this video if you need more help message me.

Read this http://forums.dlink.com/index.php?topic=44909.0

LAN cable or WiFi?

There are two ways to do a setup for a wireless adapter: * use an Ethernet cable to connect a computer to one of the LAN ports on the router; login to the router; and set the SSID (the name you are choosing for your wireless network). Then, put that Nano USB adapter into the computer, and it should load the device-drivers, and eventually will ask for the name of the SSID. Then, you can disconnect the Ethernet cable, and use the wireless connection; * as you have discovered, some routers have (and some do not have) an 8-digit 'PIN' number.