Top 20 D-Link DAP-1522 Xtreme N Duo Wireless Bridge/Access Point (DAP-1522/B) Pre-802.11n Questions & Answers


From your computer, get the MAC-address of your network adapter.
Configure the router to always give out the same IP-address for that MAC-address.

D-Link DAP-1522... | 244 views | 0 helpful votes


Hey Rolando,

On the back of the unit is a small button to reset. Use a straigtened paperclip to do so. Attached is an image of what it should look like. b86d4bfe-0100-4d89-87bc-74360b9790d9.jpg

D-Link DAP-1522... | 208 views | 0 helpful votes


Click on reset button and hold it about 20 second after some your router will be reset .

D-Link DAP-1522... | 79 views | 0 helpful votes


If the page does not open then you don't have a connection to the router. Make sure your cable is attached to the router and computer. You can't do the initial install wireless usually.

D-Link DAP-1522... | 101 views | 0 helpful votes


If it is under warranty, contact the manufacturer, and get it replaced.

D-Link DAP-1522... | 633 views | 0 helpful votes


It should work "out-of-the-box".
Be sure to connect using "straight-through" (not "cross-over") Ethernet cables.
Connect from the 'WAN' port on the router to your DSL-modem (or cable-modem).
Power-off the DSL/Cable modem.
Power-on the DSL/Cable modem.
Power-off the D-Link.
Power-on the D-Link.
Reboot your computer.
You should be good.

D-Link DAP-1522... | 143 views | 0 helpful votes


Setting up a wireless router with a Windows client can be complicated.
There are a number of measures and options that have to be understood, and it's all too easy to make a mistakes--but D-Link provides an easy-to-walk-through configuration system to help you set up your D-Link wireless router.

Plug one end of the Ethernet cable into the DSL modem.

Then plug the other end into the "WAN" port on the back of the D-Link wireless router.

Connect wired computers to any of the other Ethernet ports on the router using another Ethernet cable.

Access the D-Link Configuration Screen

Open your web interface and type "http://192.168.0.1" into the address bar, then hit "Enter" or "Return."

Use "Admin" as the username and leave the password blank when the login screen appears.

Click "OK." You should now see the D-Link configuration screen.

Set Up General Security

Change your administrative password by clicking on the "Tools" tab and choosing the "Admin" button. Enter a new password under the "Administrator" heading.

Confirm it, and click "Apply."
Disable the wireless Local Area Network (LAN) if you don't need to use the wireless access and you want to make sure no one else is able to access your network.

Under the "Home" tab, choose "Wireless" and select the "Off" option.

Enable Wireless Encryption Protocol (WEP)

Locate the "Home" tab in the D-Link Configuration screen, and click on the "Wireless" button.

Use the "Open System" button beside "Authentication."

Select the "Enabled" button next to "WEP," and set the encryption key to "128 bit."

Set the "Key Type" to "ASCII" and choose a 13-digit password for the "Key 1" field.

Write down the password in a secure location.

Click "Apply."

Change the SSID

Change the SSID to make it more difficult for others to locate and use your network by clicking on the "Home" tab and locating the "Wireless" button.

Change the default SSID to one of your choosing, then click "Apply."

Disable SSID broadcasting.
Under the "Advanced" tab, click on "Performance" and check off the "Disabled" box. Again, click "Apply."
Filter MAC Addresses

Click the "Advanced" tab in the D-Link "Configuration" screen and select the "Filters" button.

Choose the "MAC Filters" and click on "Only Allow Computers with MAC Address Listed Below to Connect to the Network."

Enter the name and MAC address of the computers allowed to access the network, beginning with the one you are currently configuring.

Click "Apply."

D-Link DAP-1522... | 101 views | 1 helpful votes


If you have forgotten this password, you will have no choice but to reset the router to factory defaults.

Reset Procedure: With the router powered on, Press and hold the reset button (on the back of the router) for 10 seconds and release. The lights on the front of the router should all flash and reboot.)-

D-Link DAP-1522... | 73 views | 1 helpful votes


Access D-Link's support-site: ftp://ftp2.dlink.com/PRODUCTS/DAP-1360/

Choose 'REV. A' or 'REV. B' or 'REV.C'.

Download the instructions for your router.

D-Link DAP-1522... | 119 views | 0 helpful votes


Setting up a wireless router with a Windows client can be complicated.
There are a number of measures and options that have to be understood, and it's all too easy to make a mistakes but D-Link provides an easy to walk through configuration system to help you set up your D-Link wireless router.

Plug one end of the Ethernet cable into the DSL modem.


Then plug the other end into the "WAN" port on the back of the D-Link wireless router.

Connect wired computers to any of the other Ethernet ports on the router using another Ethernet cable.
Access the D-Link Configuration Screen

Open your web interface and type "http://192.168.0.1" into the address bar, then hit "Enter" or "Return."
Use "Admin" as the username and leave the password blank when the login screen appears.
Click "OK." You should now see the D-Link configuration screen.
Set Up General Security

Change your administrative password by clicking on the "Tools" tab and choosing the "Admin" button.

Enter a new password under the "Administrator" heading.
Confirm it, and click "Apply."
Disable the wireless Local Area Network (LAN) if you don't need to use the wireless access and you want to make sure no one else is able to access your network.
Under the "Home" tab, choose "Wireless" and select the "Off" option.
Enable Wireless Encryption Protocol (WEP)

Locate the "Home" tab in the D-Link Configuration screen, and click on the "Wireless" button.
Use the "Open System" button beside "Authentication."
Select the "Enabled" button next to "WEP," and set the encryption key to "128 bit."
Set the "Key Type" to "ASCII" and choose a 13-digit password for the "Key 1" field.
Write down the password in a secure location.
Click "Apply." Change the SSID

Change the SSID to make it more difficult for others to locate and use your network by clicking on the "Home" tab and locating the "Wireless" button.
Change the default SSID to one of your choosing, then click "Apply."
Disable SSID broadcasting. Under the "Advanced" tab, click on "Performance" and check off the "Disabled" box. Again, click "Apply."
Filter MAC Addresses

Click the "Advanced" tab in the D-Link "Configuration" screen and select the "Filters" button.
Choose the "MAC Filters" and click on "Only Allow Computers with MAC Address Listed Below to Connect to the Network."
Enter the name and MAC address of the computers allowed to access the network, beginning with the one you are currently configuring. Click "Apply."

D-Link DAP-1522... | 90 views | 0 helpful votes


To reset the router password you have to locate the reset button on the back of the router. While the router is turned on, press and hold the reset button for 10 to 15 seconds. Once released the router should reset. After reset, go to http://192.168.1.1
You should be able to login using new password.

D-Link DAP-1522... | 343 views | 0 helpful votes


Connect your computer to the router.
Assuming Windows 7, click the "Start" button.
Into the search-box, type 'CMD' and press ENTER.
Type 'IPCONFIG /ALL'.
Look for the IP-address of the "gateway" (or "DHCP-server").
Type that IP-address into your web-browser.

D-Link DAP-1522... | 740 views | 2 helpful votes


You posted your question in December 2013.
Do you still need an answer?

D-Link DAP-1522... | 201 views | 0 helpful votes


You can do a reset to default settings. OR using the on-line setup, change/remove Security Key, refer to the User Manual here: http://www.dlink.com/-/media/Consumer_Products/DAP/DAP%201522/Manual/DAP%201522_Manual_EN_US.pdf

D-Link DAP-1522... | 275 views | 0 helpful votes


These answers on all these sites are very confusing. Here's what I did to solve the issue of not connecting with a browser. 192.168.0.50 does not work nor does http://dlinkap.local. or whatever else is printed on the device. On my PC that is hard wired to my router, I logged into my router, checked which wireless devices were connected and found that dlinkap (note this is not the SSID that is printed on the device) was assigned 192.168.0.4. Set my browser to 192.168.0.4 and off we go to configure the extender.

D-Link DAP-1522... | 1,901 views | 0 helpful votes


Maybe you have the wrong 192... Go command prompt and type in "ipconfig" without the quotes. scroll up and find the default gateway (default gate way . . . : 192...) and type that in your browser and press enter.
If that doesn't work, go to your network connections and right click on the one that is connected click properties, click on Internet Protocol Version 4, click properties, and make sure all the settings are automatic. Restart computer, repeat first part.
If that doesn't work, reset your router and access point. Than reconnect and repeat first part.

D-Link DAP-1522... | 58,916 views | 13 helpful votes


Refer to page 3 of the Quick Install Guide listed on the web site below.

There are multiple ways to configure this router and do not wish to provide HOW TO without knowing how you have it set-up.

www.dlink.com/products/default.aspx?pid=DAP-1522&tab=3

D-Link DAP-1522... | 325 views | 0 helpful votes


You can connect the desktop and the laptop to the router, and the router to your satellite modem.

D-Link DAP-1522... | 366 views | 4 helpful votes


the manual is free , at dlink dot com
you push the reset button for long time per manual 15sec (iirc)
the release it and now all defaults are set.
per the manual, google dir-655 manual.
easy as pie if you just read the manual.

D-Link Computers... | 27 views | 0 helpful votes

Not finding what you are looking for?
D-Link DAP-1522 Xtreme N Duo Wireless Bridge/Access Point (DAP-1522/B) Pre-802.11n Logo

Popular Tags

34 questions posted

Ask a Question

Usually answered in minutes!

Top D-Link Computers & Internet Experts

Mike

Level 3 Expert

4369 Answers

k24674

Level 3 Expert

8091 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Are you a D-Link Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

D-Link Computers & Internet

  • D-Link Computers & Internet

Most Popular Question

cannot access either dlinkap or

  • Computers & Internet
Loading...