20 Most Recent Kenmore 35622 Upright Vacuum Questions & Answers

Take the filter out and hold your hand over the filter connection. Turn it on and see where the air is being bypassed. What you see should suggest the fix.

I think your site is a scam to get people to sign up. No one gets their answer for free. I have no job and can't afford to pay to get this fixed, especially by people I can't see.

hi from uk not conversant with your vac but if it has only one belt that drives the roller brush ? i would suspect that the actual roller has split in centre remove roller to check it? suggest you renew drive belt to provide extra life if it has not been replaced recently or at all?

Is the smell rubber or electrical. If rubber then the belt is slipping and needs to be replaced, they stretch after awhile. Also is the brush roll turning freely, or is it bound up, it may have to be replaced. If the smell is electrical, then probably the motor is going bad and will have to be replaced.

There is some help in the link https://www.google.com/search?q=Kenmore+116-31912100++upright+vacuum+cleaner+Removing+the+handle+release+pedal ..

I don't have specific information on the Kenmore upright vacuum cleaner model number 116.31912100 or the part number 8174906, but I can provide you with general guidance on how to remove and install pedals on some vacuum cleaner models. Keep in mind that procedures may vary between models, so use the following as a general guide:

Removing the Pedal:

1. Unplug the Vacuum Cleaner: Ensure the vacuum cleaner is unplugged to prevent any electrical accidents.
2. Turn the Vacuum Cleaner Over: Lay the vacuum cleaner on its back so that you have easy access to the underside.
3. Locate the Pedal Assembly: Identify the pedal assembly on the underside of the vacuum cleaner. It is usually connected to the height adjustment or other features.
4. Release Tabs or Screws: Look for tabs or screws securing the pedal assembly in place. Use a screwdriver or the appropriate tool to release these tabs or screws.
5. Disconnect Linkages: Some pedal assemblies are connected to linkages that control various functions. Disconnect any linkages carefully.
6. Remove the Pedal Assembly: Once the tabs, screws, and linkages are disconnected, carefully remove the pedal assembly from its housing.

Installing the Pedal:

1. Position the New Pedal: If you are replacing the pedal, position the new pedal in place.
2. Reconnect Linkages: If your vacuum cleaner has linkages, reconnect them to the appropriate points on the new pedal assembly.
3. Secure the Pedal: Use screws or tabs to secure the new pedal assembly in place. Make sure it is securely fastened.
4. Test the Pedal: Manually operate the pedal to ensure that it moves smoothly and engages the desired function.
5. Turn the Vacuum Cleaner Upright: Once the pedal is securely in place, turn the vacuum cleaner upright and plug it back in.

If you're uncertain about any steps or encounter difficulties, it's recommended to consult the user manual for your specific model or contact the manufacturer's customer support for assistance. They may provide detailed instructions or guidance tailored to your vacuum cleaner's model and part.

change your filters both of them Emer Vacuums Vacuum Cleaner PartsVacuum Cleaners Powered by Network...

There isn't one! I checked yesterday when I answered your first question. https://www.google.com/search?q=Kenwood+bu4022+service+manual ..

It should be in the power head to the side of the hinge. Sears says there are no parts presumably because it has reached its service life. https://www.searspartsdirect.com/model/61rux2nv6w-000582/kenmore-bu4022-upright-vacuum-parts https://www.google.com/search?q=kenmore+intuition+bu4022+replace+power+head+switch ..

The hose assembly model number 11621714110 is a genuine OEM (Original Equipment Manufacturer) part for use with a variety of appliances, including vacuum cleaners and washing machines. This hose assembly may be used to connect various parts of the appliance, such as the pump and the tub, or to connect the appliance to a water source. I hope this information is helpful! Let me know if you have any other questions.

Hi, I'm getting 13.7 cubic feet. To reconfirm, you can call kenmore customer service by dialing 1-844-553-6667. Thank you.

lock stuck open or broke

More likely to be a bad connection or brushes on the motor that need replacing. Classic symptom of bad / worn brushes.

Press and hold the filter reset button for 3 seconds to reset the indicator. The control may need to be replaced if it isn't able to reset. [url=http://spacebarcounter.org]Spacebar counter[/url]

Thank you very much. I'm up and running again. My retractable cord jump track and got stuck. Thank you thank you. And I did it myself with your directions. Linda

It isn’t the belt. Hair builds up in other places besides the brush. The device is made to come apart. Take it apart an clean out both ends on the shaft of roller brush. Remove tangled hair on the shaft and the brushes.

https://www.searspartsdirect.com/brand/0582/kenmore-parts?sid=sem:bing:SB+-+Kenmore+-+Appliances+-+BMM+-+tROAS+l_DM1+7a3c:1191871242423714:%2Bkenmore%20%2Bappliance%20%2Breplacement%20%2Bparts:c&msclkid=4f141d4557761a7ddc8a7fedec5aee42 Check this Kenmore parts site