Re: Can select 1st gear and 2nd gear but am unable to...
The gearbox does not need to be relpaced. The bike has a bent shift fork. The engine comes out then gets a complete tear down to get to the bad fork. This will probably cost $1200 or so. Call a dealer and get an estimate. Please rate my answer. Thanks.
Testimonial: "Thanks very much for your advice and help!!!!! much appreciated!"
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
? 9:53
https://www.youtube.com/watch?v=2TCHzIvAvRQ
Mar 6, 2014 - Uploaded by luke Fugate
This is a video to show you how to adjust a Three speed on the column to ... It's great not having to wind the engine and transmission just to take off in 2nd or 3rd gear. ... It was ALWAYS getting stuck between 1st and 2nd gear. .... 1977 c10 3 On The Tree ' How to Drive a 3 Speed Column Shift - Duration: ...
All they know is that they put their gear selector in "D" for Drive and their vehicle ... But when internal problems cause the transmission to act up, it takes a fair amount .... In Chrysler three-speed automatics, changing the fluid to ATF+3 can also help ...kickdowns to get the transmission to downshift to 1st from 2nd or 3rd gear.
Wikipedia1 Overview; 2 Unsynchronized transmission; 3 Synchronized transmission; 4 Internals.... gear speeds by blipping the throttle when shifting from 2nd into 1st. ... In a synchromesh gearbox, to correctly match the speed of the gear to that of the ... Even in transmissions that do not feature direct drive, it's an advantage for the ...
If the clutch is a problem you will have difficulty selecting 1st only as the gears would be spinning from the engine revs.. I would say that the front input shaft (clutch shaft) bearing is failing allowing miss alignment of the synchros and not allowing proper engagement of the gears synchro rings. It means removal and repair to the gear box so the clutch can be inspected while the box is out.
Hello, problem is from the gear box. The gear box has developed a fault and that is why it starts out in 1st will not shift in 2nd will jump in to 3rd . Also, have your gear oil check to be sure it is not short. You need to take the Dodge to your mechanic before the problem gets worse. This is not a DIY (do it yourself) job. If you don't take it to your mechanic on time, you might end up damaging the gear box which is expensive to replace. It is still repairable for now. I hope the above is clear. Regards.
my suzuki baleno 2001 mod manual has a problem with the gear box. i can go 1st,2nd and 5thgear but can not get in to 3rd and 4th gear...what do you think it could be? thanks my email is: [email protected]
There is a vacuum controlled selector valve on the selespeed alfa's it tricky to get at and expensive to replace. Have it sent to an alfa specialist or main dealer and they ll sort it
You need to give the car a scan, preferably with VCDS (or VAS at a dealer). If limp mode is activating (lit up gear selections), then it will be storing codes. The fact that it works to a degree could be good news, the gear box has likely not failed. Could be the F125 selector switch, which is a common fail at this age.
hi fro uk this is a common problem on many cars not just hyundai and ita most common cause of synchro mesh failure on2nd and 3rd gear is believe or not a bad driving habit! it goes like this when you set off in 1st then cange up 2nd gear whilst accellerating holding gearstick? in back position then change up 3rd gear still holding gearstick! in a forward position then? when up to 4th gear we let go of gearstick?? now just by holding g/stick whilst in 2nd and 3rd the slightest pressure also brings the synchro ring into play whilst gear already selected! so inevitably the synchro ring wears away to extent that they no longer work properly so the gearbox is none synchromesh on 2nd 3rd gears and on occasions? on 5 speed box 4th gear can become a victim ? hope you understand ? just quietly observe some peoples habits with manual boxes? as for repairs?cost? this is not a difficult job to replace all synchro rings but box has to be stripped and assesed ? the cost could escalate? but if you want quick turnround? a matter of hours? a recon box with warranty? is other option ? BUT would not advise risking a 2nd hand box probably worse or same as ? whichever choice you take you can check clutch at same time if milage is high? now some good advice! personally this is not a dire problem just a niggleproblem which if you take time in changing gears you can o/come gritty gear change save money for now till it is more affordable ? if you know any old timers truck drivers ? these are the guys who will show you how to drive /change gears none synchro mesh before it was ever invented ? hope this helps daughter but practice on gears and rid of the bad driving habit so many do not realise they have will make her a better experienced!driver
×