SERPENTINE BELT SPECS DIagram

To let you know I found these links with a google search for (2006 honda accord v6 belt diagram)
2003-2007 Honda Accord Serpentine Belt Replacement (2003, 2004, 2005, 2006, 2007) - iFixit Repair Guide
Video on how to change belt. Near the end of video he shows diagram.
How to Replace the Serpentine Belt on a 2003-2007 Honda Accord 3.0L V6 Step-by-Step - YouTube

2003-2013 Honda Accord V6 Accessory/Serpentine Belt Replacement - YouTube

Search Results

images for diagram on how to replace a serpentine
How To Install Replace Serpentine Belt Oldsmobile Alero 99 ...? 3:33https://www.youtube.com/watch?v=jkzXTt43uwwFeb 9, 2012 - Uploaded by 1A Auto PartsHow To Install Replace Serpentine Belt Oldsmobile Alero 99-04 2.4L .... There should be a belt routing diagram on the frame rail or under side ...serpentine belt install 3.1/ 3.4 v6 - YouTube? 4:00https://www.youtube.com/watch?v=GYoWuvEZ2DcMay 6, 2013 - Uploaded by JoeTheAutoGuythis a serpentine belt install video on a 3.1 liter gm v6 , 3.4 liters are the same in ... Replacing the alternator or serpentine on anyOldsmobile Alero 99-04 3.4 Liter ... Serpentine Belt Replacement 1995-2005 Chevrolet Cavalier .

The picture is for a zetec. Let me know if wrong diagram?

VIDEO Change Serpentine Poly Drive Belt tensioner on Mercedes Benz...

Serpentine Belt Replacement

Replacing Your Mercedes Belt Tensioner

mercedes benz serpentine belt diagram

Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------This will help. Thanks.

Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.

3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.

4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.

5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.

6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

that is your belt tensioner!! You pull that back when you are gettin ready to finnish putting your belt on the last pulley!! Follow diagram under hood for your specs on motor!!

2.0L Engines
See Figures 11, 12 and 13
The accessory drive belt for 2.0L engines has no provision for manual belt adjustment, since these engines use an automatic belt tensioner. Drive belt slack is taken up by the automatic tensioner.
Movement of the automatic tensioner assembly during engine operation is not a sign of a malfunctioning tensioner. This movement is the tensioner self-adjusting and is required to maintain constant belt tension.
The belt tensioner has a belt length indicator. If the indicator marks are not between the MIN and MAX marks, the belt must be replaced.
Fig. 11: Drive belt routing-2.0L SOHC engine with A/C Fig. 12: Drive belt routing-2.0L SOHC engine without A/C Fig. 13: Drive belt routing-2.0L DOHC engine