Ford Cars & Trucks - Recent Questions, Troubleshooting & Support

0helpful
1answer

My 2008 Ford F-150 5.4 l king ranch stalls when I put it in reverse.

Question edited for clarity. Question moved to correct year make model category. You are using what I call the "let's try changing this" method of auto repair and as you have found out it is expensive and doesn't work. Your vehicle is run by sensors, modules, the BCM and ECM all connected and working on a computer network. The only way is to get the services of an auto electrician who will connect a $5,000 pro grade scan tool computer and diagnose every system and module in the vehicle. One benefit is that they can record everything that is happening, when all these odd things are happening in real time. Then they can even play back the details and work out what the issue is. https://www.google.com/search?q=auto+electrician+near+me ..
8/19/2022 12:25:19 PM • 2008 Ford F-150 • Answered 5 hours ago
0helpful
2answers

2002 ford f250,gauges cut off while driving, then come back on.

indicates a problem ground point or a problem BCM board
8/18/2022 6:46:00 PM • 2002 Ford F250... • Answered 23 hours ago
0helpful
3answers

Does the ford bantam 2007 model 1600 rocam engine have a fuse for the hooter or only the no 3 relay on the diagram?

The horn is fused and will be listed in the fuse box layout within your user manual.
8/17/2022 10:21:59 PM • Ford Cars &... • Answered Yesterday
0helpful
1answer

P1132 and P1151, What can I do to fix it? Car Keeps Stalling out?

what engine is there, , size, displacement in liters or CUInches. 3.8L V6? p-0135 is a uSA federal code, all P0xxx are. P1xxx are care makers owned codes, means do not read lies on the internet about, p1,p2,and codes only read your service manual learn that bad heaters are to be fixed first 02 replaced or wires melte there.. HO2S-11 Heater Circuit (Bank 1, Sensor 1) bad O2, front of CAT sensor bank 1, aka. upstream. bank one is cylinder #1 bank side. #1 cyl is the most front cylinder on all v6 or v8. all this is me reading your service manual to you. p1132 Lack of HO2S-11 Switching, HO2S Signal High Input this fails because heater is dead. so is moot here, later yes now no. 0135 first. p1151 Lack of HO2S-21 Switching, HO2S Signal Low Input bank 2, sensor 1. (may be caused by above otherS.) H-hear, O 2 means oxygen sensors 11 is bank1 senser. 12 B1S2 21 b2s1 22 B2S2 SEE?
8/17/2022 10:19:53 PM • Ford Cars &... • Answered Yesterday
0helpful
2answers

Will a 2022 Ford explorer transmission fit my 2000 chevy silverado 4.3 liter

2wd or 4wd? oops. ext. cab? ask ford this. only or they will demand to know the vin #' or will not answer you. why not aSK THEM FIRST/ USA CAR? OR NOT? EXPORTS ARE not the same. all transmission sellers know this , forgot to ask them>? we sell none here,, even mid year the maker can make radicall changes to the transmissions and there new now electronic shifted trans and even if it fits (physically) the TCM must not be fooled or must be reprogrammed. 2000 chevy silverado 4.3 liter, PU. extended cab or not.?????? 2wd? the 2000 has 6 bolt bell housing so there is a huge problem there. 4L60E lots of variants on that box, for ages. 1992 to 2013,. sorry not 2022. ever. more off the wiki by same name 4L60E uses a 6.5" depth bell with 6 bolts for non gen 3 LS applications and a 7" depth bell with 7 bolts for LS applications. The 4L65E/70E uses a 7" depth bell and 7 bolts.<< oops ! https://en.wikipedia.org/wiki/GM_4L60-E_transmission huge limits, here and more the TCM must like your new box. (TCM/PCM) or fails hard. in 1996 , 4 solenoids now, obd2 epa laws. he last 4L60Es were only used in the GM Vans in 2013, before being replaced by the 6L80E. that is my answer VIN not seen or body of car or driveline full spec the tip of the iceberg answer, ask your transmission builder this .
8/17/2022 7:26:59 PM • Ford Cars &... • Answered Yesterday
0helpful
1answer

2014 Ford Ecosport Titanium 1.5. what are the torque sequence and value for cylinder head on it please?

There is generic information only and a video, but the sequence in the graphic is correct. You need a workshop Manual when doing work like this. Some are available online. https://www.google.com/search?q=2014+Ford+Ecosport+Titanium+1.5%2C+cylinder+head+bolt+torque ..
8/17/2022 5:27:58 PM • Ford Cars &... • Answered Yesterday
0helpful
1answer

07' Ford Focus coolant hose by battery

If I am thinking right it is a heater hose coupling it should mount into the intake if so it is a dealer item it's called a heater hose to intake coupling Good Luck
8/17/2022 5:07:24 AM • Ford Cars &... • Answered 2 days ago
0helpful
2answers

I need the firing order of spark plugs for a 2016 Ford Fiesta SE

1-3-4-2, however some British engines used a firing order of 1-2-4-3.
8/17/2022 3:19:34 AM • Ford Cars &... • Answered 2 days ago
0helpful
1answer

I have a ford Falcon mk11 xr6 6cyl can someone point out the adjusting screw that is located on the throttle cable to adjust the idle

2005 the idle should be controlled by the ECU and not adjustable.
8/16/2022 7:29:42 PM • Ford Cars &... • Answered 2 days ago
0helpful
1answer

2003 ford tauras blowing ac fuse

need to test the a/c circuit for short--failed component
8/16/2022 11:23:32 AM • 2003 Ford Taurus • Answered 3 days ago
0helpful
2answers

Headlights, high beams

No as a rule they don't fail at the same time, in fact it is unusual for the hi beam to fail ever, the problem is most likely in the turn signal/multifunction switch, this does cause your problem, have seen it many times.
8/16/2022 10:58:23 AM • 2003 Ford... • Answered 3 days ago
0helpful
1answer

High beam trouble shooting 2003 expedition

could be the multifunction switch. there may also be a headlight relay for just the high beam. check the manual for its location
8/16/2022 10:57:53 AM • 2003 Ford... • Answered 3 days ago
0helpful
1answer

I have a 2004 ford taurus and my turnsignals dont

the multifunction switch is a common problem on fords. the switch controls the wipers, turn signals, high beams and hazards, and sometimes only 1 part of it will fail. in your case it sounds like 2 parts fail at the same time.
8/16/2022 10:57:45 AM • 2004 Ford Taurus • Answered 3 days ago
0helpful
1answer

2000 ford taurus wiper problem: wiper blabes are

Check the corresponding fuse in the fuse box. If fine, could be the multi function switch that controls/adjusts wipers, blinkers, high beams, etc.. Hope this helps.
8/16/2022 10:57:33 AM • 2000 Ford Taurus • Answered 3 days ago
0helpful
1answer

My low beams don't work,

the multifunction switch that controls the wiper /turn signals,and high/low beam lights are very common for (when they get a lot of miles on them) for having problems.also I have seen a good number of these pickups that the connector (that plugs into the back of the multifunction switch)had lost the ability to properly hold the wire terminals into the connector causing a poor connection between the switch and the wiring. sometimes this can be verified without removing the column shrouds by (if equipped) tilting the tilt wheel up and down and see if the lights start working . hope this helps,thanks for using fixya
8/16/2022 10:57:07 AM • 1994 Ford F350... • Answered 3 days ago
0helpful
2answers

Ford 2003 Focus. Low beam headlights not working.

REPLACE MULTI SWITCH ON COLUM (STEERING) ON LEFT SIDE. bUY NEW ONE FIRST AND LOOK AT OLD AND SIMPLER TO CHANGE
8/16/2022 10:53:45 AM • 2003 Ford Focus • Answered 3 days ago
0helpful
1answer

No Low beam headlights

Do you know how to test automotive electrical circuits using a DMM - digital multi-meter ? Principles of Operation The headlamp switch is supplied power at all times from the smart junction box (SJB). When the headlamps switch is placed in the headlamps ON position, power is routed to the multifunction switch. Depending on the position of the multifunction switch, power is routed through one of two circuits to the SJB. If the multifunction switch is in the high beam position, power is routed through SJB fuse 12 (15A) and then on to the high beam headlamps. If the multifunction switch is in the low beam position, power is routed through SJB fuses 11 (10A) and 15 (10A) to the LH and RH headlamps, respectively. Power to the multifunction switch is available at all times for the flash-to-pass feature. Is there B+ voltage at fuse's # 11 & 15 with headlamps on an the multifunction switch is in the low beam position ? If not check for B+ voltage at the multifunction switch . Free wiring diagrams here http://www.bbbind.com/free-tsb Enter your vehicle info. year , make , model an engine . Under system click on lighting then under subsystem click headlamps . Click the search button then the blue link . Basic Electricity for Service Techs Ohm law Current Flow Opens Shorts Electric Testing Techniques You Need to Know
8/16/2022 10:52:19 AM • Ford Taurus Cars... • Answered 3 days ago
0helpful
1answer

2006 Ford Taurus. How can I unlock my door without calling anyone please?

Question edited for clarity and correct spelling of Taurus. Question moved to model category. Try some of these ways. Inflatable wedge and a coat hanger normally. https://www.google.com/search?q=how+to+unlock+ford+taurus+with+keys+locked+inside ..
8/15/2022 11:01:25 PM • Ford Taurus Cars... • Answered 3 days ago
Not finding what you are looking for?
Ford Logo

246,676 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2000 Ford Focus
2000 Ford Focus

3,730 Questions

1998 Ford Explorer
1998 Ford Explorer

2,981 Questions

2001 Ford Focus
2001 Ford Focus

2,611 Questions

1999 Ford Taurus
1999 Ford Taurus

2,346 Questions

2004 Ford F150
2004 Ford F150

2,631 Questions

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85240 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8991 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6963 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...