Here's a video on your crankshaft position sensor. 2007 Hyundai Accent Crank Shaft Sensor Replacement
SOURCE: hyundai accent, location of fuel cut off
hi from uk location of fuel safety shut off valve/switch on uk r/h drive accents is on the engine bay bulkhead in front of drivers side it is a square box with red rubber top press button may be on opposite side on l/h drives ? if activated? just press button till click ? to reset these normally only cut off on impact ? to stop elec fuel pump continuing delivering if involved in an R.T.A fire prevention
SOURCE: 2001 Hyundai accent crank position sensor needs
Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.
SOURCE: Location of sensors
IAT SENSOR IS MOUNTED INSIDE INTAKE AIR HOSE TO THE AIR CLEANER ASSEMBLY. THE MASS AIR FLOW SENSOR IS ALSO MOUNTED TO THE INTAKE AIR HOSE OF THE AIR CLEANER ASSEMBLY. O2 SENSORS LOCATION.YOU HAVE 2 # O2 SENSORS.YOU HAVE ONE THE EXHAUST MANIFOLD.THE OTHER SENSOR LOCATED DOWN AT THE CATALYTIC CONVERTER.
SOURCE: its a hyundai trajet,aa said crankshaft sensor not
it is inside the timing cover in most cases with hyundai the timing belt will have to be removed so the crank gear can come off the sensor is usually behind the gear especially if it is a 6cyl if it is a 4 cyl then the wire goes behind the timing belt make sure the timing marks are lined up so when you reassemble it is lined up
Testimonial: "Thank you for the advices Ill get cracking on it"
SOURCE: need to locate o2 sensor location bank 1 sensor 2
You need to check two things.
First, there is a heat shield on top of the front of the motor where the o2 sensor you already replaced is. It's got (4) 12mm bolts. Remove it and check the exhaust manifold (big thing you put the o2 sensor into) for cracks. If there are any cracks, you'll get o2 sensor codes. Replace the manifold.
Second, if the manifold is fine start the car and listen to the exhaust pipe under the engine for leaks. Or if you already know the exhaust is loud... that's gonna do it too. A leaking exhaust pipe on an Accent will set secondary o2 sensor codes.
SHOULD you try to change it yourself, you will need a 7/8" wrench, and a new o2 sensor, or flex pipe, or manifold depending on what's broke. Do NOT touch the tip of the new or old o2 sensor to ANYTHING when you take it out or install it or it will be ruined permanently. Run the car until it's at it's normal operating temperature. Raise the vehicle, and take the o2 sensor out of the car (see below to understand which one) using the 7/8" wrench or if you got fancy and bought an 02 sensor tool... use it.
Replace whatever parts are bad (manifold or pipe) or just replace the sensor you need. Then restart the car and take it to a parts store and have them clear the code. The code (and check engine light) won't return right away, it usually takes a few days. If you did everything right you should be good. If not, it's not a terribly expensive job to have done and by now you should be able to explain to them what's wrong based on what you found when you looked at the car. Just tell them everything you checked and what you saw.
Education: I'm not sure where that half baked answer about o2 sensor 1 being near cylinder one came from but here's the real deal.
Sensor 1 is always BEFORE the catalytic converter
Sensor 2 is always AFTER the catalytic converter
Bank 1 and Bank 2 refer to which SIDE of the exhaust on 6 and 8 cylinder engines. Bank 1 is usually left side, Bank 2 is usually right side.
So... O2 sensor B1S1 refers to the O2 sensor BEFORE the converter on the LEFT side of the motor.
1,703 views
Usually answered in minutes!
×