Serpentine belt routing 1987 e150 302 engin - 1987 Ford Econoline

Application:
With A/C

Kia_Sedona_2002-2006
Accessory Drive Belts

• ACCESSORY BELT ROUTING
• INSPECTION
• REMOVAL & INSTALLATION

Print

Accessory Belt Routing

Fig. Accessory serpentine belt routing-3.5L engine

Fig. Accessory serpentine belt routing-3.5L engine

Fig. Accessory serpentine belt (A) routing-3.8L engine

Inspection

Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.

Removal & Installation

1. Disconnect the negative battery cable.
2. Rotate the auto tensioner clockwise to release tension, then remove the drive belt.

To install:

1. Install drive belt (A). Route the belt over the components in the following order: Crankshaft pulley - A/C pulley - idler pulley - generator pulley - water pump pulley - P/S pump pulley - tensioner pulley.
2. Rotate auto tensioner arm in the counter-clockwise moving auto tensioner pulley bolt with wrench.
3. After putting belt on auto tensioner pulley, release the auto tensioner pulley slowly.
   
   

   Fig. Accessory serpentine belt routing-3.5L engine
   
   
   

   Fig. Accessory serpentine belt (A) routing-3.8L engine
   

Fig. Accessory serpentine belt routing-4.3L, 5.0L and 5.7L engines without A/C




Fig. Accessory serpentine belt routing-4.3L, 5.0L and 5.7L engines with A/C

Fig. Accessory serpentine belt routing-6.5L Diesel engines

Fig. Accessory serpentine belt routing-6.6L Diesel engines

Hope this helps (remember to rate this answer).

Fig. Serpentine accessory drive belt routing-3.0L (VIN U) engine


Fig. Serpentine accessory drive belt routing-3.0L (VIN S) engine


Fig. Serpentine accessory drive belt routing-Ford 3.0L (VIN U) engines


Fig. Serpentine accessory drive belt routing-Ford 3.0L (VIN S) engine


Fig. Serpentine accessory drive belt routing-Ford 3.4L SHO engine


Fig. Water pump drive belt routing-Ford 3.4L SHO engine
i wasnt sure what engine you had hope this helps good luck

The link below will take you to a page with several diagrams. Your car has 4 different engine sizes but you should find the appropriate diagram on this page. Best of luck.
Greg

87 Monte Carlo

Not sure of your engine size since you didn't post it so please the applicable one for you. Also, please don't forget to rate! Thanks!


Serpentine drive belt routing with A/C-GM 2.2L engine


Serpentine drive belt routing without A/C-GM 2.2L engine


Serpentine drive belt routing-GM 2.4L engine

You didn't list your motor size so please pick the applicable diagram:


Accessory serpentine belt routing—4.8L, 5.3L & 6.0L engines


Accessory serpentine belt routing—5.7L engines with A/C


Accessory serpentine belt routing—5.7L engines without A/C


Accessory serpentine belt routing—6.5L Diesel engines


Accessory serpentine belt routing—7.4L engines


Accessory serpentine belt routing—8.1L engines

call a parts store they usually can provide you the routing for serpantine belts good luck getting it right though it can be tricky pay close attention to how the belt is routed :)

Hello srevenipsen: My name is Roger I will help you. I am sending you a picture of the belt routing for a engine with or with out A/C. Please rate the quality of the information. This insures you received the right information. Thank You for using FixYa.Roger