Charge circuit hj60 diesel

Potentially sensors. Or sensors and dashboard lights. Sometimes it can happen that small things prevail.

The electronic switch on the top of the fuel filter housing is the fuel filter warning switch.
To reset the warning light on the cluster you need to do this:
1. With the ignition switch off, disconnect the fuel filter warning switch connector.
2. Turn the ignition switch from off to ON.
3. After more than 3 seconds but less than 60 seconds have elapsed, reconnect the connector.
4. After approximately 3 seconds have elapsed with the fuel filter warning switch closed, the
system confirms the deletion of the illumination information by turning off* the warning light.

check fuses first, cab and bay
if all good
scan the PCM .
or get it scanned.

The instrument cluster (10849) carries out a display proveout to verify that all warning/indicator lamps and monitored systems are functioning correctly. When the ignition switch (11572) is in the ON position with the engine (6007) off, the following indicators will illuminate:

• CHECK ENGINE/malfunction indicator lamp (MIL).
• CHECK GAGE warning indicator.
• Charge system warning indicator.
• Anti-lock brake warning indicator (ABS).
• Safety belt warning indicator (60second proveout).
• Air bag indicator.

• An indicator is inoperative - CHECK ENGINE/malfunction indicator lamp (MIL)

• Bulb.
• Circuitry.
• Instrument cluster printed circuit.
• Powertrain control module (PCM) (12A650).

• GO to Pinpoint Test N .

Running the car will drain the battery it if it's not charging ! An if your charging light is on it isn't charging ! Did you check power an grounds on the alternator ? There is a single heavier wire on the back of the alternator, this should have battery voltage ! You may want to take this to a ASE certified repair shop !
Functionality
With the ignition switch in the RUN position, voltage is applied through the warning indicator I circuit 904 (LG/RD) to the voltage regulator. This turns the regulator on, allowing current to flow from battery sense A circuit 35 (OG/LB) to the generator field coil. When the engine is started, the generator begins to generate alternating current (AC) which is internally converted to direct current (DC). This current is then supplied to the vehicle's electrical system through the output (B+) terminal of the generator.
Once the generator begins generating current, a voltage signal is taken from the generator stator and fed back to the regulator S circuit 4 (WH/BK). This voltage feedback signal (typically half the battery voltage) is used to turn off the warning indicator.
With the system functioning normally, the generator output current is determined by the voltage of the A circuit 35 (OG/LB). The A circuit 35 (OG/LB) voltage is compared to a set voltage internal to the regulator, and the regulator controls the generator field current to maintain the correct generator output.
The set voltage will vary with temperature and is typically higher in cold temperatures and lower in warm temperatures. This allows for better battery recharge in the winter and reduces the chance of overcharging in the summer.
Battery Positive Output (B+) Circuit 38 (BK/OG)
The generator output is supplied through the battery positive output (B+) terminal on the back of the generator to the battery and electrical system.
I Circuit 904 (LG/RD)
The I (ignition) circuit 904 (LG/RD) is used to turn on the voltage regulator. This circuit is powered up with the ignition switch in the RUN position. This circuit is also used to turn the charging system warning indicator on if there is a fault in the charging system operation.
A Circuit 35 (OG/LB)
The A (battery sense) circuit 35 (OG/LB) is used to sense battery voltage. This voltage is used by the regulator to determine generator output. This circuit is used to supply current to the generator field (rotor). The amount of current supplied to the rotor will determine generator output.
S Circuit 4 (WH/BK)
The S (stator) circuit 4 (WH/BK) is used to feed back a voltage signal from the generator to the regulator. This voltage is used by the regulator to turn off the charging system warning indicator. The S circuit is fed back externally on external mounted regulator generators.
Visual Inspection Chart Mechanical Electrical

• Battery case, posts, hold-down clamp, cables and connections
• Generator drive (serpentine) belt for condition and tension to make sure there is no slip between the belt and the pulley. For additional information, refer to Section 303-05 .
• Battery charge
• Generator pulley

• Battery junction box (BJB)Mega Fuse
• Battery junction box fuse:
  • 11 (20A)
• Central junction box (CJB) fuse:
  • 30 (30A)
• Circuitry
• Charging system warning indicator
• Cables

1. Check the operation of the charging system warning indicator lamp (instrument cluster). Normal operation is as follows:
   • With the ignition switch OFF, the charging system warning indicator should be OFF.
   • With the ignition switch in RUN and the engine off, the charging system warning indicator light should be on.
   • With the engine running, the charging system warning indicator light should be off.

1. Verify the battery condition. Refer to Section 414-01 .

Normal Charging System Voltages and Charging System Warning Indicator Operation Ignition Switch Position A Circuit 35 (OG/LB) S Circuit 4 (WH/BK) I Circuit 904 (LG/RD) Generator B+ Circuit 38 (BK/OG) Battery Engine to Battery Ground Charging System Warning Indicator Operation OFF 12 volts 0 volts 0 volts 12 volts 12 volts 0 volts Off RUN-engine off 12 volts 0 volts 1-3 volts 12 volts 12 volts 0 volts Illuminated RUN-engine running 13-
15 volts 1/2 battery voltage 13-
15 volts 13-
15 volts 13-
15 volts 0 volts Off

1. If the customer concern is verified after the initial inspection, refer to the Symptom Chart to determine which tests to carry out.
2. • The charging system warning indicator is on with the engine running (the system voltage does not increase)
   • Circuitry.
   • Voltage regulator.
   • Generator.
   • GO to Pinpoint Test B .
   Your whole problem is the alternator is not charging , a couple tests with a volt meter would tell you !

The warning chime sounds if the parking lamps (13200) or the headlamps (13008) are left on after the key has been removed from the ignition switch lock cylinder and either front door (20124) is opened. There is a chime module that controls this .
The safety belt warning chime (10D840) (also called the central processing unit or CPU) is an audible warning system and timing circuit. The system components include:

• Timing circuit safety belt switch.
• Dome lamp switches.
• Safety belt warning indicator switch which is an integral part of the front safety belt buckle end (61203).
• Ignition switch (11572).
• Headlamp switch.

The warning chime sounds and the safety belt warning indicator illuminates when the ignition switch is placed in the ON position and the LH front safety belt is not buckled.
Key In Ignition Warning
The warning sounds if the key is left in the ignition switch lock cylinder when either door is opened and the ignition switch is in the LOCK or OFF position.
Don't any of chimes work ?

• The Headlamp on Reminder Chime Is Inoperative/Does Not Operate Properly

• Circuits.
• Fuse junction panel.
• Warning chime module.

• GO to Pinpoint Test D .

Let me know ,mite work this out !
Don't

According to the Nissan service manual the procedure to Reset the Air Bag System Warning Light is as follows:
1. Turn ignition switch from OFF to ON.
2. Air Bag warning light is on for 7 seconds and turns off, turn the ignition switch OFF within 1 second after the light goes out.
3. After ignition switch is turned OFF, wait for more than 3 seconds.
4. Repeat steps 1 to 3 twice. (Perform 3 times in total.)
5. Turn Ignition switch ON.
6. The SRS light should be reset.
If the warning light can not be reset I'd suggest you contact your Nissan dealer for more information and a proper diagnostics check as there be a fault with the airbag system.
Alan

Do warning lights and gauges come on, when key is turned to on?
If yes, check for power on the small wire at starter solenoid mounted on the starter with the key held in start. If power at the solenoid, take starter off and test for a bad starter or solenoid. If no power at solenoid when key held over to crank, work back to the switch in the start circuit-starter relay, clutch or neutral safety switch,-power from the start wire out of switch is not getting to the starter solenoid.
If no warning lights or gauges work with key in on position, power is either not getting to switch (bad maxi-fuse or fuse link, or bad battery connections-clean and tighten, recheck)-or the switch itself is not sending power out. Check if battery is charged up. Check all connections and grounds for loose, poor connections.
The start circuit starts at the battery, then to ignition switch, then out of ignition switch on the start wire to the clutch switch (or neutral/park on automatics), and on , ending at the starter solenoid on the starter. Somewhere in your starting circuit, power is lost. Start at the battery-check charge, check connections, check ignition switch.

with ignition turned on to 11 there are certain warning light that do stay illuminated but will go off when engine has started ie oil pressure/ charging/ m i l light /handbrake warning will go off when h/brake released so if battery is flat know anyone with jump leads?? could help you start ?

If you have changed the alternator and regulator, about all that could be left would either be a short circuit that is draining current away, or a bad ignition warning light bulb. That is because the power to energize the field of the alternator, comes through this dash bulb.