Plumbing - Page 4 - Recent Questions, Troubleshooting & Support

Is the Tap body in 2 parts or is it just 1 solid body?

1. Turn off the water supply valves under the sink.
2. Turn on the faucet handle to release any water remaining in the lines.
3. Locate the set screw on the handle or the underside of the dome, depending on the faucet model.
4. Use an Allen wrench to remove the set screw by turning it counterclockwise.
5. Once the set screw is removed, grip the dome or handle with your hands and pull straight up to remove it from the faucet body.
6. If the dome is difficult to remove, you may need to use a strap wrench or pliers to loosen it before pulling it off.
7. After the dome is removed, you should have access to the faucet cartridge, which can be replaced if necessary.

It's important to follow the manufacturer's instructions for your specific faucet model, as the steps may vary slightly depending on the design. Additionally, it's a good idea to have a bucket or towel handy to catch any water that may drip out of the faucet during the removal process.

there may be an issue with the hose or the weight that is attached to the hose under the sink. Here are some steps you can follow to troubleshoot the issue:

1. Check the weight: There should be a weight attached to the hose under the sink. This weight is designed to help the hose retract back into the faucet. If the weight is loose or not in the correct position, it can affect the retracting ability of the hose. Make sure the weight is securely attached to the hose and is in the correct position.
2. Check the hose for obstructions: The hose may not be retracting properly due to an obstruction. Turn off the water supply to the faucet and disconnect the hose from the faucet. Carefully inspect the hose for any kinks or blockages. If you find any obstructions, gently straighten out the hose and remove the blockage.
3. Check for damage to the hose: The hose may not be retracting properly due to damage. Check the hose for any visible signs of wear and tear, such as cracks or tears. If the hose is damaged, it will need to be replaced.
4. Lubricate the hose: Over time, the hose can become dry and lose its flexibility. Apply a small amount of silicone lubricant to the hose to help it move more freely.

Maybe try their Tech 844#... https://www.deltafaucet.com/sites/delta/files/2019-12/Touch_troubleshooting_guide.pdf Best to you

Taps lock up and rust. Although the outside is nice and shiny chrome, the inside is brass and they use steel screws that rust in place. Turn off the water, replace the whole thing. Take the parts back where you got them and buy the new one. When you get the new one, remove screws and removeable parts and grease them up with Vaseline.

The ITT Magna pump LD7AC pressure switch is used to control the pressure in a water system. If the pressure switch is not staying on or the jets are not running, it could indicate a problem with the pressure switch or the water system. Here are some potential solutions to try:

1. Check the air pressure: Make sure that the air pressure in the pressure tank is set correctly. If the air pressure is too low, the switch may not stay on.
2. Check the pressure switch: Make sure that the pressure switch is properly adjusted and not damaged. The switch should be adjusted to turn on at the correct pressure and turn off at a slightly lower pressure.
3. Check the water system: Make sure that the water system is not losing pressure. This could be due to a leak in the system or a clogged water filter.
4. Check the electrical connections: Make sure that the electrical connections are secure and not corroded. Loose or corroded connections can cause the switch to malfunction.

If these solutions do not resolve the issue, it may be necessary to seek professional assistance to diagnose and repair the problem. A qualified technician will be able to diagnose the issue and repair the pump or pressure switch as necessary.

If your Everpure faucet is leaking at the handle, the problem could be a faulty O-ring or a worn-out cartridge. Here are the steps you can follow to fix the leak:

1. Turn off the water supply: Before you start working on the faucet, make sure to turn off the water supply to prevent any accidents.
2. Remove the handle: Use a screwdriver to remove the screw that holds the handle in place. Once the screw has been removed, you can gently pull the handle off the faucet.
3. Check the O-ring: Look for an O-ring around the base of the handle. If the O-ring is damaged, worn or missing, it can cause water to leak from the handle.
4. Replace the O-ring: If the O-ring is damaged, replace it with a new one. You can purchase O-rings at a hardware store or online.
5. Check the cartridge: If the O-ring is in good condition, the problem could be a worn-out cartridge. You may need to remove the cartridge and replace it with a new one.
6. Reassemble the faucet: Once the O-ring or cartridge has been replaced, reassemble the faucet by putting the handle back in place and tightening the screw.
7. Turn on the water supply: Finally, turn the water supply back on and test the faucet to see if the leak has been fixed.

If you're having difficulty fixing the leak or if the problem persists, it may be best to contact Everpure customer support for further assistance. They can help you diagnose the problem and recommend the best solution.

Question edited for clarity, 'Hmms' to 'hums'. Question moved from Cars and Trucks category. If it hums, it means the start/run capacitor on the motor has failed and needs replacing. https://www.google.com/search?q=GOULD+BGR75+humms ..

It sound like you may be in fault mode. This unit is not known to us in North America. Make sure your tank level switch is operating correctly and also make sure there are no airlocks in the pump. Page 14 onwards. These units can be serviced by Pentair, as they are an expensive unit to buy https://www.onga.com.au/_repository/1/documents/L100195_0719_Waterswitch_OM.pdf https://www.google.com/search?q=onga+water+switch+pump+cleaning+instructions ..

Once you have removed the screw from the handle, you may be able to gently pull the handle away from the valve. Some handles may have a small set screw on the side that needs to be loosened first. If the handle does not easily come off, gently tap it with a soft rubber mallet or use a handle puller tool to carefully remove it. If the handle is still stuck, consult the manufacturer's instructions or a plumber for further assistance.

To remove the handle on a Kohler 12176, follow these steps:

1. Turn off the water supply to the faucet.
2. Look for a screw or set screw on the handle that is holding it in place.
3. If there is a screw, use a screwdriver to loosen and remove it.
4. If there is no screw, use a handle puller tool to gently pry off the handle.
5. Once the handle is removed, you can access the valve stem and replace any damaged parts if necessary.

Note: If you are unsure about the process, consult the Kohler 12176 owner's manual for specific instructions or contact a professional plumber for assistance.

It's possible that the solenoid valve in the touchless faucet is not functioning properly, and needs to be replaced. Another possibility is that there is a loose or broken wire in the electrical circuit that powers the solenoid valve. You may want to check the connections and wiring, and consult a plumber or electrician if necessary, to help diagnose and repair the issue.

Try claiming on their 5 year warranty. It is probably a worn o-ring or a worn ceramic cartridge in there. If you phone them, they will tell you the part that has probably failed. This link shows parts for the HT-200, but shows the cartridges and o-rings. https://www.chicagofaucetshoppe.com/Franke-Little-Butler-Parts-s/11466.htm

Franke Little Butler

https://www.franke.com > shared > pdfs > LB2000 PDF Franke Little Butler. Spare Parts & Warranty. Franke Little Butler. Installation and User Guide. Hot and Cold Water Dispensing System. Model Series LB2000. ..

It's possible that the gasket between the top and bottom case has worn out and needs to be replaced. You can check the manual for the system or contact the manufacturer for more information on how to replace the gasket. It's also possible that the screws need to be tightened to prevent the leaking. If the pump is not turning on, you may want to check the float switch and make sure it's functioning properly.

The cause of the automatic pump control failure light turning on and the pump not turning on after pressure drops could be due to a variety of reasons, including: -A faulty pressure switch -A clogged or damaged pressure tank -Wiring issues, such as damaged or loose connections -A faulty control board -A broken impeller or worn out pump motor. It is recommended to have a professional diagnose and repair the issue.

The problem could be a failure or wear of the seal under the cap that is causing the leak. You can try to remove the cap by delicately turning it with a flathead screwdriver in the counterclockwise direction. If this does not work, it may be necessary to seek the help of a plumber or the manufacturer.

Plumber Near Me Callaghan [FREE Quote] Power Plumbers

https://powerplumbers.com.au > newcastle > callaghan If you find that your Callaghan plumbing system is running slowly and problematic,you could call our Callaghan plumbers to assist you with a solution. Callaghan ... 191 reviews

Callaghan Plumber ' The Plumbing Life Saver ' 24/7 Plumbing ...

https://theplumbinglifesaver.com.au > callaghan-plumber

With The Plumbing Life Saver, there are no compromises and you can get it all - outstanding quality at a fair price. What our clients highlight is our highly ...

Find a Plumber or an HVAC Contractor in Callaghan, VA ...

https://www.rheem.com > pros-in-callaghan-va

Find a Pro By Callaghan, VA ... Whether you're looking for a master plumber to install a new water heater, a pool and spa expert to install or repair your pool ...

Plumber Callaghan ' Blocked Drain & Hot Water Repair Plumber

https://rightsolutiontrades.com.au > plumber-callaghan You'll get the right solution for you. Using CCTV camera equipment our Blocked drains Callaghan Plumber can inspect your drains to identify exactly what is ...

The often happens when the new cartridge is misaligned. https://www.google.com/search?q=Installing+new+Grohe+cartridge+470800 ..

i'm guessing ...but... take it off ..take it to the outside faucet or water hose hold the hose end tight on the faucet outlet and turn it on to back flush it what went in should come out .. but have you checked the screen on the spicket (where the water comes out) that usually unscrews an you will see a screen inside there that can get clogged in addition to several plastic aerator bits that can get clogged and this is a LOT easier than removing the faucet and back flushing it ..

1. Check the suction line for blockages or kinks: Make sure that the suction line is clear and that there are no blockages or kinks in the line that could prevent the pump from priming.
2. Check the impeller: Make sure that the impeller is not clogged or damaged, as this can prevent the pump from priming.
3. Check the voltage: Make sure that the voltage to the pump is within the specified range.
4. Check the pressure switch: Ensure that the pressure switch is functioning correctly and that the pressure switch cut-out is set to the correct pressure.
5. Check the thermal overload: Ensure that the thermal overload is functioning correctly and that the pump is not overheating.
6. Consult the manual: Consult the manual for specific troubleshooting and service information for your Goulds J5S model.