Toner and developer indication appears and machine does not copy toshiba 161

Did you use the original toner and original drum? Toner high in developer. While pressing [0] and [5] simultaneously, turn the power ON. The following message will be displayed. Key in code [2000] and press the [START] button. The display changes as follows.
Indicates the controlled value of the auto-toner sensor output. Press the Up or Down button to change the value.(245,128)
Please the OK button.

in old model copier you must adjust td sensor after replace developer. in toshiba 161you must:
1.press0and5 in numeral keys
2.turn on machin .aj mode shown
3.inter 200 by numeral keys and start or interput
Machin work for minutes .
Press interput ana turn off then on

Power off the machine, remove the toner then power on the machine with no toner install let the machine run when it ask for toner install

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

IF YOU YOU HAVE DONE MORE THAN 50.000 COPIES WITH THAT DEVELOPER MATERIAL REPLACE THE DEVELOPER MATERIAL. BUT CHANGE THE SEALS AND MAIN CHARGE GRID. THAT SHOULD SORT YOU OUT. ALL THE CONSUMABLES ON THAT MACHINE IS 50K COPIES

Sir, i added new toner and new developer but my printout is dull. What i do?

Hi:

Your copier has reached it's predetermined time to have its developer changed. This is something that a qualified tech would have to take care of.

Andrew

hi when the copiers shows that need toner it is becouse there is no toner in the mix of developer, this is caused by a wrong toner in the machine, check that the toner is the one the machine use there are few copiers like lanier that seems to use the same cartridge but change the gear that turns the toner in the machine, move manually the gear in the cartridge by looking that the toner actually it is ok, activate the motor that moves the toner cartridge and check thatis is moving, also check the gears on the developing unit becouse if any of them dont move the toner never get the sensor of the developer unit and shows the signal of lack of toner

jesus contreras ortega

Dear sir; First I have let you know the copier use toner not ink , want to know how many left over; 1, press and hold down the left exposure key until indicator flash, then press and hold the "%" key for 5 seconds.the window will show out the percentage. LO means less than 10%, press left exposure key to escape.if there still have problem please let me know, otherwise please be generously give me rating. thank you. HAVE A MERRY CHRISTMAS !!!

Hi,

The developer you need to purchase is 1620 , and the drum unit also the 1620, you can see this number in the toner catridge itself. or in the toner catridge box. Regd. the 161 you need to purchase the products name 1620 number and the concerned part like developer, drum, toner, some gears etc.

Technical Service Procedure
Correct procedure for service of TOSHIBA e-Studio 161
When the spanner light and the developer (sun) light are illuminated it is time for a service.
* Try and run the PM Service and drum life counters together.
* Part that are required for a 50,000 copy service (OD 1620 DRUM, D1620 DEVELOPER, BL1620D DRUM BLADE)
* Clean and inspect drum unit.
* Clean all optics and glass.
* Clean and rewire transfer corona.
* Clean and check main charge needle electrode [saw tooth]
* Clean and check fuser units including blades, rollers and scraper fingers.
* Clean erase lamps and ozone filters.
* Clean and check all feed rollers.
* Clean machine inside and out.
* Replace the required parts.
* Reset mini maintenance counters:
* [CLEAR] > [EXPOSURE] > [CLEAR ]> [EXPOSURE] and the machine will die.
* Input [20] [START] [01] [START]“000””000” will flash on the display.
* Reset the drum life counter:
* Input [24] [START] [07] [START] "000"000" will flash on the display
* Reset developer life counter:
* Input [42] [START] [01] [START] “000””000” will flash on the display.
* Once all the part have been replaced and the counters been reset, check the copy quality.
* Notes: Application of the patting powder is for reducing the friction between the drum and cleaning blade. If the application of
patting powder is neglected, the drum and cleaning blade may be damaged. Please clean off the patting powder before putting the
cleaner unit into the machine.
Developing doctor gap adjustment
1) Loosen the developing doctor fixing screw A.
2) Insert a thickness gauge of 1.5mm to the three positions at 20mm and 130mm from the both ends of the developing
doctor as shown.
3) Push the developing doctor in the arrow direction, and tighten the developing doctor fixing screw. (Perform the same
procedure for the front and the rear frames.)
4) Check the clearance of the developing doctor. If it is within the specified range, then fix the doctor fixing screw with
screw lock.
* When inserting a thickness gauge, be careful not to scratch the developing doctor and the MG roller.
CHANGING A TRAY’S PAPER SIZE SETTING
Follow these steps to change a tray’s paper size setting.
* The paper size setting cannot be changed when the machine has stopped temporarily due to running out of
paper or a misfeed, or during interrupt copying.
* During printing (even in copy mode), the paper size setting cannot be changed.
* A5 (ST) size paper can only be selected in upper paper tray.
* Do not load paper that is a different size than the paper size setting. Copying will not be possible.
Hold down the [PAPER SIZE ENTER]
key for more than 5 seconds to
set the selected paper size.
The currently selected
paper feed location
indicator will blink and
the corresponding paper
size (which is currently
set) indicator will light
steadily. All other
indicators will go out.
If the machine has two paper trays,
use the [TRAY SELECT] key to
select the paper tray for which you
wish to change the paper size setting.
Each time the [TRAY
SELECT] key is
pressed, a paper tray will
be indicated with a
blinking paper feed
location indicator.
Use the [ORIGINAL SIZE ENTER] key
to select the paper size.
The indicator of the
selected paper size lights
up.