Question about Haier Heating & Cooling

1 Answer

My tumble dryer its not heating but i do get voltage on it so what can be wrong

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 726 Answers

Clean all the filters
if its still not heating it will be the thermostat

Posted on Jul 07, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replaced ac unit with new compressor. Fires up as usual but compressor wont start.No fault code coming on controller. Whats the problem?


possible causes include
excessive gas
low gas
relay not working,
faulty thermostat
faulty start/run capacitor
bad circuit board

Jan 03, 2017 | Heating & Cooling

2 Answers

My thermostat is set on 68 degrees and it shows room temperature is 68, but the furnace still kickson, Honeywell said it has a 1 degree difference. so what's the problem then?


Yes there is a one degree tolerance, in fact my heater just kicked on and it is set to 67 and the inside temperature reads 67. It is also a Honeywell.

Dec 28, 2016 | Heating & Cooling

1 Answer

70 series boiler model #70-148. I need the pionts/box that controls the thermosstat. It runs but it does not matter what the thermosstat is set at. I was told by a pro that the points are sticking. I


Be sure the thermocouple is still working, clean the contact points with crocus cloth and be sure the voltage going in to the controller is correct.

Jan 21, 2015 | Heating & Cooling

1 Answer

Johnson Starley boiler main board fuse blowing


Chances are the fuse on the circuit board is for control circuit protection. Take note of the location of all the thermostat connections on the circuit board and remove them. Do this with the power OFF. Replace the fuse and re establish power. If the fuse did not blow, the problem is in the wiring to or from the thermostat. It could even have the insulation rubbed through and making contact with the side of the boiler or a mouse could have chewed through the insulation causing a short to a metal object.

Once the issue with the thermostat wiring is resolved, reinstall the low voltage connections and you should be good to go.

Jan 08, 2015 | Heating & Cooling

1 Answer

Repair infrared space heater


It might have a fuse that has been blown internally. This may have happened to protect it from over heating because it was left on too long or something went bad and it got too hot.

Dec 08, 2014 | Heating & Cooling

1 Answer

Conair Lysol hand held steamer


Does it tell you to add salt to the water?(I have a cheapo little steamer that requires salt to increase the conductivity of the water-it just creates steam by running AC voltage through the water in the tank)

May 25, 2013 | Heating & Cooling

1 Answer

I have a Kenmore dehumidifier 58053701300. It worked fine for maybe five summers, but I couldn't get it going this past June. It just would not turn on. I checked the outlets. No problem. No...


I will start to dig into this one and see what I can find as far as measurments for voltage. In the mean time, you said the bucket was ok, but did you check to see if the shut off float switch is operating and moving freely and not bound up some how. It should also have a slight clicking sound as the switch is made and unmade.

Dec 04, 2011 | Heating & Cooling

2 Answers

Flashing re co


Re Co stands for Recovery Mode. That means if you have programed your thermostat to be at say 72° at 5:00 then it should kick on in Recovery Mode several minutes before 5 in order to reach that temperature. This is normal and doesn't indicate that something is wrong, just that your thermostat is trying to reach or recover the programed temperature.

Feb 08, 2008 | Heating & Cooling

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Haier Heating & Cooling Experts

Tom Chichester

Level 3 Expert

29036 Answers

Caleb Brunson
Caleb Brunson

Level 2 Expert

54 Answers

Taylor

Level 2 Expert

202 Answers

Are you a Haier Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...