My lg 32lc7d remote wont program the codes

To program your Sanyo GXDB remote to work with your Pioneer Elite VSX 33 receiver, you can try the following steps:

1. Turn on the Pioneer Elite VSX 33 receiver manually using the power button located on the receiver itself.
2. Hold down the "Code Search" button on your Sanyo GXDB remote until the LED light on the remote stays lit or blinks.
3. Press the "TV" or "DVD" button on the remote, depending on which device mode you want to program the receiver to.
4. Enter the corresponding code for Pioneer receivers. You can find a list of Pioneer remote control codes in the instruction manual that came with your Sanyo GXDB remote or by searching online. Enter the code using the number buttons on the remote.
5. Point the remote at the Pioneer receiver and press the "Power" button. If the receiver turns off, it means the remote has been successfully programmed. If not, repeat the process using a different code from the list until you find the one that works.
6. Once the remote successfully turns off the receiver, press the "Code Search" button again to save the code. The LED light on the remote should turn off or stop blinking.
7. Test the remote by pressing other buttons, such as volume up/down or channel up/down, to ensure it is functioning properly with your Pioneer Elite VSX 33 receiver.

If you're still having trouble programming the remote, consult the instruction manual that came with the Sanyo GXDB remote or contact Sanyo customer support for further assistance.

Glenda, remote urc 3021 code for LG DVD PLAYER, LG dvd try codes, 0591, 0869, 0741, 1906
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
http://voxrightnow.custhelp.com/app/answers/detail/a_id/7692/~/programming-the-one-for-all-urc3021-universal-remote-control-(3-devices)
RC LG DVD Codes
How to Program Universal Remote Codes for Universal Remotes

If you know the setup codes to your TV brand, the common way to set up is:
Direct Code Entry

1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.

If you wish to know more setup procedure to many more remote control brands, check this site.

Most of the combo units are hit and miss on using entry level remotes, Learning remotes or high end remotes are you two best bets.

You can try these Sony Remote Sanyo VCR codes:046, 044, 035, 033, 038

Follow these steps to program the remote control.

1. Turn on the component to be programmed.
2. On the remote control, press and hold the SET button.
3. While holding the SET button, press and release the POWER button
4. Release the SET button.
5. Press the appropriate component button for the component being set up.
6. Using the number pad, enter the component's manufacturer code. NOTE: If more than one code number is listed for the manufacturer, repeat the procedure, entering one code at a time until you find one that works.
   
7. Press the ENT button.
8. Point the remote control at the component.
9. Press the POWER button to verify operation.

Your universal remote would have seperate selection buttons for VCR and DVD. If you don't have a VCR button, use AUX. Try programming each function seperately - DVD code for your manufactirer on the DVD button and VCR code for your manufacturer on the VCR button.

the default for the rh7823w remote is to operate lg tvs. Popping out the batteries should reset the default. my manual saysto select a different tv hold down the tv power button, press the number buttons for the manufacturer code then release power button.

codes are

LG/Goldstar 1(default), 2
zenith 1,3,4
samsung 6,7
sony 8,9
hitachi 4

good luck

1. While holding down TV POWER button, press the
number buttons to select the manufacturer code
for your TV (see the table below).
2. Release TV POWER button.

Code Number
LG / GoldStar: 1 (Default), 2
Zenith: 1, 3, 4
Samsung: 6, 7
Sony: 8, 9
Hitachi: 4

Try this through your Remote, it should automatically search & detect devices automatically without the need to know the codes.


USING CODE SEARCH FUNCTION
If your TV, VCR, DVD, etc. does not respond after you have tried all the codes
for your brand or if your brand is not listed, try searching for your codes by
following the steps below.
1. Turn on the device you wish to program.
2. Press and hold CODE SEARCH/SETUP until the INDICATOR
LIGHT lights, then release.
3. Press and release the device button for the device you are
programming (TV, VCR, DVD, etc.). The INDICATOR LIGHT will
blink once then remain lit. For AUX, press AUX then the device
button you are assigning to AUX.
4. Press and release POWER until your device turns off. Wait at least
2 seconds between each time you press POWER. Important: You
may have to press POWER up to 250 times.
5. When your device turns off press the ENTER/SAVE button. The
INDICATOR LIGHT will go off.

Turn on dvd player by hand using your lg tv control push set up dvd plus code.pointing for 15 seconds.