WHEN I PUSH THE FILTER BUTTON THE LIGHT COMES ON, THE SCREEN SHOWS FILTER ON , BUT PUMP DOES NOTHING . WAS WORKING FINE PUMP WAS REBUILT 1 WEEK AGO. THIS IS AQUA LOGIC .

They might be on a timer and only work at certain hours of the day, if the time is set wrong............

The blower wheel probably is dirty. The unit is sensing that not enough air is flowing across the AC coil.

I had the same problem, Check Filter light blinking and beeping, could not select drying type or start dryer. Short story, turned out to be the Less time button was stuck pushed in. Long story, a week before I had replaced the drum rollers and belt, everything was working fine for the week after then this problem. Totally by accident, after trying all the recommended actions (unplugging, pushing buttons, etc.) leaning on the right front corner would stop the beeping and allow the machine to work. Pushing all the buttons, I found the Less time button would not click. Apparently, when I took the control panel off to change the rollers and belt I flexed the control panel enough to misaligne the button and switch. Pulling the back of the control panel loose and making sure the push button and switch were aligned and working correctly everything works fine now.

LIGHTING OR POWER SURGES ARE THE BIGGEST KILLER OF PUMP MOTORS. ASK THE GUY WHO REBUILT IT IF HE CAN HELP YOU OUT. I'M LOCATED IN FLORIDA AND ITS THE LIGHTNING CAPITAL ! LAST STORM WE HAD IN 5 MINUTES THERE WAS 1000 STRIKES AND THE LAST BIG STORM 68,000 STRIKES. HECK I'VE BEEN HIT AND SEEN STRIKES JUST YARDS AWAY FROM ME.. COOL, BUT NOT , IF'N YA KNOW WHAT I'M SAY'N

take too shop, that rebuilt the tranny. see if they cant do a better job. they may tell you the problem. lol.

www.batteryship.com

look up tomtom 510 - or whatever model you have
Order the battery..........comes with manual and tools to fix it
only 20.95
it works

cheaper than sending it in!!!!!!
These are genuine replacement parts!!

Laura

Possibly you might need the Brew Head Screen and/or filter basket cleaned of built up coffee oils. Depending on how much you use it, is best to clean it every week or couple of weeks.
Remove brew head screen and filter basket, also if you have a screw in the filter basket and soak with in a cleaner for removing oils (not descaler) at: www.urnex.com or Dezcal etc.
Or, if you have not used it in awhile you might need to prime the pump manually:
Fill water tank.
Turn power on.
Open the steam knob all the way.
Press the coffee button.
Put a cup under the steam pump wand.
Wait until you see a steady flow of water and no air.
When you see the flow of water, close the steam knob.
Turn off the coffee button.
Now the machine should be ready to brew an espresso.
For further details email: [email protected] or the service center:
Electra-Craft
41 Woodbine St
Bergenfield NJ 07621
phone 201-439-1700
fax 201-439-1701
[email protected]
www.electra-craft.com

We have a toshiba gigabeat f20. today it worked fine, listened to it for hoursbefore turning it off. turned it on within a hour to play it and got a blank screen. nothing in the environment could have caused this. battery had been replaced a week before. so, took the case off to opened it and take a look. realized that one of the plug ins for the screen had come loose or slightly lifted inside. it did not totally unplug, just not pressed down tight. pushed it back in. put the case back on. hit the power button and it's back on, nothing that had been previously loaded was lost.

I guess make sure the filter didn't unseat itself first, also check the O-rings, etc. to make sure they didn't roll off their position on the filter. If that's all OK, you really need to find that gurgle sound cause that's likely the water you are missing going "somewhere" it's not supposed to go. Look all over for water leaks even if you have to pull the unit out from the wall... keep looking!