Question about Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher

Open Question

Bosch she55 diagnostic - Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A F04 Err is flashing on my Bosch double oven. Please can you tell me what this means?


The only F04 error on a Bosch oven is with the Bosch 5000 Series wall oven. On this model, the problem is with the door latch. Unplug (or turn off at the circuit breaker) the oven. Turn it back on after a few seconds. When the power comes on, the oven should do a self-test of the lock mechanism. If the error persists, you'll need to do some diagnostics to determine if the lock is faulty. The problem could also be with the wiring or the control board didn't register the correct signal from the lock sensor.

Please add a comment with the model number of the wall oven for more assistance and any possible parts lists. You may want to call for service if you aren't comfortable doing this work. You probably need to get the oven out of the wall cavity for some of the diagnostics.

I hope this helps.

Cindy Wells

Feb 24, 2017 | Bosch Ovens

1 Answer

How do I run a diagnostic test on the Bosch shu5315uc/u12? The cycle time of my dishwasher is at least 4-5 hours.


Long running time on a Bosch dishwasher is almost always a blown solder joint at the heater relay on the control board. You can resolder the joint, replace the relay or replace the control. Control board part number is 00266746.

Jan 13, 2015 | Bosch Dishwashers

1 Answer

How do i run a test / diagnostic mode for the bosch sge63e05uc (evolution series) dishwasher?


Are the instructions on how to run the diagnostic test listed in the manual? FYI, I couldn't run the test on my Bosch DW because it was just too broken. Over the years the dishwasher essentially fried its own circuit board with excessive heat, which I learned is a problem common to Bosch DW's. Bosch told me the lifespan of my model was 10 years; mine was 11 years old (but was repaired once or twice). I replaced it with a Miele; no problems yet after 4 1/2 months.

May 22, 2014 | Bosch 24 in. SHU53 Built-in Dishwasher

1 Answer

How do I run a self diagnostic on Bosch Classic Electronic SGU53E75AU/86?


Before going to the controller it might be better to verify the heater or thermostat (NTC).
If you want to know the part details refer this schematic

http://www.bosch-home.co.uk/store/spareparts/Builtunderdishwasher/SGU53E75AU/86

It is interactive and you can switch between assembly drawings and parts lists. The heater and thermostat are drawing 4.

Apr 26, 2014 | Bosch Dishwashers

1 Answer

Bosch Dishwasher model SHU66C06 doesn't enter wash cycle


this sounds like flow sensor failure,it it fails machine will either not fill up or fill and drain without washing its a cheap part to replace and is fitted downstream of inlet valve behind l/h/s side panel either attached to inle hose or heat exchanger.

Mar 03, 2017 | Bosch 24 in. SHU66C02 / SHU66C06 Built-in...

1 Answer

Have bosch sgs 6312gb it's not filling with water in machine


If it works when water is added the the over flow switch is ok
Here is the diagnostics guide Bosch dishwasher service guide



11_23_2011_6_10_58_pm.jpg

Nov 23, 2011 | Bosch Dishwashers

1 Answer

How do you run the diagnostic on a bosch dishwasher model # SHE44C06Uc/22. it counts down to one on the timer and runs forever. can't find it model # diagnostics anywhere. thanks


Resoldering the relay, regardless of how proficient one is at soldering, will not be a long term solution. The melted/burned solder joint is a secondary result of the initial failure, which is the relay itself. There is a solution that is more permanent and less costly than replacing the control with a new one.
Do a search for Bosch 266746 control and you will locate someone who has studied the problem and found a safe, long term solution.

Nov 16, 2010 | Bosch 24 in. SHE44C02UC / SHE44C06UC /...

1 Answer

How do I clear code E27 from my Bosch washing machine?


I had to call a certified bosch repair center. They sent someone out who entered some sort of code to put the washer into diagnostic mode. Once it was there, the code cleared and my washer worked again.
I asked for the code, and the repairman wouldn't give it to me.

Aug 31, 2010 | Bosch Logixx WFT 2806 Front Load...

3 Answers

Bosch SHV 6800 dishwasher, 2HR error


Bosch dishwasher all cycles start at 2H and get hungup on 1 min.

Jul 02, 2008 | Bosch SHU9950 Dishwasher

Not finding what you are looking for?
Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1466 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18402 Answers

Are you a Bosch Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...