Treadmill error codes 3 - Exercise & Fitness

Ask the manufacturer

Try below:

ERROR CODE
DESCRIPTION
E1
Speed error (The treadmill running speed is 3.2 kph faster than the displayed
speed). The treadmill will stop immediately when the console detects this error.
E2
Speed error (The treadmill running speed is 3.2 kph slower than the displayed
speed). The treadmill will stop 16 seconds later after the console detects this
error.
Troubleshooting / Resetting error codes
In the rare event of the treadmill displaying an error code ("E" followed by a number), simply reset
the computer by:
1. Step off the treadmill. Ensure that you are clear of the running belt.
2. Turn the treadmill off at the master power switch located near the motor housing.
WARNING: Ensure nothing is positioned near or under running belt which may possibly block
it's normal operation.
3. Turn the treadmill on at the master power switch.
4. Ensure that the Safety Tether Key is securely and properly installed onto the console or just
reinstalling the Safety Tether Key can also reset the display.
If the above does not clear the error code, please contact the nearest Dealer/Service Center

LifeGear 97320 Owner Manual Page 17

What Does Your Treadmill's Error Code Mean? - LifeSpan

www.lifespanfitness.com/.../what-does-your-treadmills-error-code-mean

Free
May 21, 2015 - If the running belt stops after 6 seconds of starting the treadmill, this may indicate that either the ... If there is no belt movement, or you notice a burning smell coming from the motor area, this ... An E6 or E7 error code is an incline error code. ... This will cause the incline motor to raise the running deck up.

[PDF]ERROR CODES: ADDITIONAL ERROR CODES:

www.gympart.com/TSB/.../Treadmills/.../Sportsart%20Error%20Codes.p...

ERROR 6: INCLINE ERROR - CHECK INCLINE OPERATION AND CALIBRATION. ERROR ... ERROR 1-1: AC SERVO ERROR - AC SERVO MOTOR ENCODER HAS FAILED ... error codes listed by category: treadmills, bikes, elliptical trainers. ...ERR1 Condition 1: Press speed key; walk belt doesn't move; ERR1 appears.

[PDF]Error Code Troubleshooting Guide

see the diagram attached for the speed sensor. test for open or faulty. clean it, and tight for plug or connector.
2) Test the input voltage motor, if there are the motor need repair
3) Test the output voltage board, for input voltage motor, if there are NOT the board is faulty.
God bless you

see this steps and fix it. .Of course you must read your instr. manual or download from www. iconservice.com
When the treadmill is not in use, press the "Stop," "ENTER" and "QUICK START" buttons in rapid succession. The "RESET" button can also be used, in place of the "Stop" button.

2 Press the "ENTER" button three times to access the treadmill's error log.

3 Press the up or down arrows to scroll through the error codes, if necessary for club or personal logging purposes.

4 To view the treadmill's odometer reading when a particular error code was elicited, press "SELECT" while a particular error code is displayed.

5 To clear the error log, press "QUICKSTART" for a minimum of four seconds while viewing the list. Prompts will appear on the display and let you know when the log has been deleted.

My motorized Treadmill is showing error E09 how can l clear the error?

Dear Sir:

I will try to help you.

• 1

When the treadmill is not in use, press the "Stop," "ENTER" and "QUICK START" buttons in rapid succession. The "RESET" button can also be used, in place of the "Stop" button.

• 2

Press the "ENTER" button three times to access the treadmill's error log.

• 3

Press the up or down arrows to scroll through the error codes, if necessary for club or personal logging purposes.

• 4

To view the treadmill's odometer reading when a particular error code was elicited, press "SELECT" while a particular error code is displayed.

• 5

To clear the error log, press "QUICKSTART" for a minimum of four seconds while viewing the list. Prompts will appear on the display and let you know when the log has been deleted

If you need further assistance, please reach me, sincerely.

God bless you.

E.CUADRA
MANAGUA, NICARAGUA. C.A.

Dear Sir:

Please try with this Reset system for Code:

• 1

When the treadmill is not in use, press the "Stop," "ENTER" and "QUICK START" buttons in rapid succession. The "RESET" button can also be used, in place of the "Stop" button.

• 2

Press the "ENTER" button three times to access the treadmill's error log.

• 3

Press the up or down arrows to scroll through the error codes, if necessary for club or personal logging purposes.

• 4

To view the treadmill's odometer reading when a particular error code was elicited, press "SELECT" while a particular error code is displayed.

• 5

To clear the error log, press "QUICKSTART" for a minimum of four seconds while viewing the list. Prompts will appear on the display and let you know when the log has been deleted.

If you need further assistance, please reach me. sincerely. God bless you.

E.CUADRA

MANAGUA, NICARAGUA. C.A.

Matrix Treadmill, (T5x, T7x) Control Board, Motor, 1.5KW/90~264V, JHT01

From time to time, error codes will pop up on your treadmill. It just takes a quick second to clear the error log and get the treadmill up and running again.
1.When the treadmill is not in use, press the "Stop," "ENTER" and "QUICK START" buttons in rapid succession. The "RESET" button can also be used, in place of the "Stop" button.
2.Press the "ENTER" button three times to access the treadmill's error log.
3.Press the up or down arrows to scroll through the error codes, if necessary for club or personal logging purposes.
4.To view the treadmill's odometer reading when a particular error code was elicited, press "SELECT" while a particular error code is displayed.
5.To clear the error log, press "QUICKSTART" for a minimum of four seconds while viewing the list. Prompts will appear on the display and let you know when the log has been deleted.
I hope you find it very helpful.