Thermoheat dtu torpedo heater reads E1 error - Protemp 125000 BTU Kerosene Forced Air Heater with Thermostat

Question 1

0helpful

1answer

What does error code E1 on a tankless water heater mean?

generic code for thermistor (temp sensor).

E1 Error Code This is an error on the thermistor. For instance, if your EcoSmart tankless water heater unit is displaying this E1 error code, it shows that you are being notified of the EcoSmart inlet thermistor that is not reading the proper temperature.Sept 22, 2021

Troubleshooting EcoSmart Tankless Water Heater Error Codes

May 19, 2022 • RVs

0helpful

1answer

I have a dyna glo RMC 40 NGT vent less wall heater that I would like to convert to propane, I need to know which conversion kit to buy, and where. Thank you.

dyna glo natural gas heater Questions & Answers - Fixya

www.fixya.com > Forum > Tags

dyna glo ventless rmc50 ngt can this heater be changed from natural gas to propaneuse, ... Dyna Glo Natural Gas conversion to LP Gas I have a Dyna-Glo natural gas space ... Question about D-E36 Infra-Red Wall Mounted Panel Heater ... dyna glo heater model #RMC-40GT I believe on your particular model , that you ...

Parts for Dyna Glo, Thermoheat and Dyna Glo Pro Heaters

spaceheaterparts.com/category.sc?categoryId=13

Shop Dyna Glo, Thermoheat, Dura Heat, Workhorse LP and oil fired htrs ... Circuit Board 2201181 Dyna Glo & Thermoheat 150k Nat Gas Htr RMC-FA150NGDGD ... This spark plug (ignitor) is used on Dyna Glo and Thermoheat 40K btu LP.

Propane Wall Heaters - Walmart.com

www.walmart.com > ... > Heaters

WalmartDyna-Glo IR18NMDG-1 18,000 BTU Natural Gas - Infrared Vent Free Wall Heater. $170. ... Dyna-Glo 40K Liquid Propane 360-Degree Tank Top Heater. $88.00 ... Dyna-Glo Deluxe RMC-FA125DGD Portable Gas Powered Forced Air Heater.

1352062 Dyna Glo Natural Gas conversion to LP Gas

162.220.53.34/F/.../t1352062-dyna_glo_natural_gas_conversion_lp_gas

Jan 12, 2016 • Heating & Cooling

0helpful

1answer

When plugging in my reddy heater 110 it blows air & no heat and then goes off.

Hi,

Here are a couple of tips that I wrote that tell you how to troubleshoot a Torpedo or Reddy heater...

Reddy Heater - Troubleshooting Torpedo Heaters

Torpedo Heater Pump Pressure Adjustment

heatman101

;]]]]]]]]]]]]]]]]]]]]]]

Feb 12, 2011 • Reddy Kerosene Heater with Thermostat:...

0helpful

1answer

Comes on but cuts out and bellows smoke from filter.

Hi,

Here are a couple of tips that I wrote that tell you how to troubleshoot a Torpedo or Reddy heater...

Reddy Heater - Troubleshooting Torpedo Heaters

Torpedo Heater Pump Pressure Adjustment

heatman101

Jan 29, 2011 • Milwaukee Tool Master Heater 70,000 BTU...

0helpful

1answer

I went online to get help with a Dyna Pro and paid 12.00 for some assistance on 1/13/11.I have not heard anything in response. It was having and E1 error and asked for help or product manual. I will call...

Hi,
You need to send and email to [email protected]....

If you are still have trouble...

Here are a couple of tips that I wrote that tell you how to troubleshoot a Torpedo or Reddy heater...

Reddy Heater - Troubleshooting Torpedo Heaters

Torpedo Heater Pump Pressure Adjustment

heatman101

Jan 28, 2011 • Reddy Heater-170,000 BTU Kerosene Deluxe

0helpful

1answer

Dynaglo forced air kerosene heater fuel not getting to nozzle. replaced hoses, cleaned nozzle, cleaned fuel filter, pressure gauge reads OK.

Hi,

Here are a couple of tips that I wrote that tell you how to troubleshoot a Torpedo or Reddy heater...

Reddy Heater - Troubleshooting Torpedo Heaters

Torpedo Heater Pump Pressure Adjustment

heatman101

...........

Jan 13, 2011 • All-Pro Kerosene Garage Shop Heaters - All...

0helpful

1answer

I have an old master 150000 btu air forced portable heater. Everything has run fine until today. The kerosene level got low and it started sputtering. i unplugged the unit and filld with a1 kerosene. Now...

Hi,

Here are a couple of tips that I wrote that tell you how to troubleshoot a Torpedo or Reddy heater...

Reddy Heater - Troubleshooting Torpedo Heaters

Torpedo Heater Pump Pressure Adjustment

heatman101

]\\\\\\\\\\\\\\\\\\\

Dec 16, 2010 • All-Pro Forced Air Kerosene Space Heater...

0helpful

1answer

Why will the unit not even start? Before it quit it would puff a few times and then re light and then it wouldnt do anything. im stumped ive read a few things but nothing is makin sence

Hi,

Here is a tip about troubleshooting Torpedo Heaters

Reddy Heater - Troubleshooting Torpedo Heaters

heatman101

Dec 01, 2010 • Mr. Heater MH175KT Open Flame Utility

2helpful

2answers

Heater starts and then runs a short while then stops but produces heavy cloud of smoke .. ignition is off ... model 55b

Hi,
Here are a couple of tips that I wrote that tell you how to troubleshoot aTorpedo or Reddy heater...

Reddy Heater - Troubleshooting Torpedo Heaters Torpedo Heater Pump Pressure Adjustment
heatman101

Nov 28, 2010 • Reddy Heater-30-55,000 BTU Variable

0helpful

1answer

HAVE A 150,000 BTU REDDY HEATER, WITH COVER OFF IT WORKS FINE, WITH COVER ON T-STAT BLINKS ON DISPLAY AND AFTER ABOUT 5 SEC BLOWER CUTS OFF, HAS C3 ERROR CODE. IS THIS A THERMO PROBLEM

Hi,
Here are a couple of tips that I wrote that tell you how to troubleshoot aTorpedo or Reddy heater...

Reddy Heater - Troubleshooting Torpedo Heaters Torpedo Heater Pump Pressure Adjustment
heatman101

..,//,

Oct 16, 2009 • Reddy Heater-40,000 BTU Kerosene w/T'stat

Question 2

Donni Steen

Master 687 Answers
Posted on Feb 05, 2017

Donni Steen

Master

Joined: Jan 05, 2009

Answers

687

Questions

0

Helped

446665

Points

2142

These are some possible causes:
1. Wrong pump pressure
2. Dirty Air Output,Air Intake or Lint Filter.
3. Dirty Fuel Filter.
4. Dirt in Nozzle.
5. Dirty Photocell Lens.
6. Photocell Assembly not
Properly installed.(Not seeing the flame)
7. Bad electrical connection between photocell and MAIN PCB assembly.
8. Defective Photocell.

If all those check out ok, then check these:
1. No fuel in tank.
2. Wrong pump pressure.
3. Carbon deposits on spark plug and/or improper gap.
4. Dirty fuel filter.
5. Dirt in Nozzle.
6. Water in fuel tank.
7. Bad electrical connection between ignitor and MAIN PCB assembly.
8. Ignitor wire is not attached to spark plug.

skan8 Oct 11, 2023

I have this small torpedo heater with a thermostat, and when I turn it on, the spark keeps flashing for 16 seconds and then it turns off showing E1. I fiddle with the gas pressure regulator on the reducer and sometimes I find the spot where it doesn't turn off, but it's way too low a pressure.

×

Related Topics:

Thermoheat dtu torpedo heater reads E1 error - Protemp 125000 BTU Kerosene Forced Air Heater with Thermostat

1 Answer

Donni Steen

Add Your Answer

Attachments: Added items

Related Questions:

What does error code E1 on a tankless water heater mean?

Troubleshooting EcoSmart Tankless Water Heater Error Codes

I have a dyna glo RMC 40 NGT vent less wall heater that I would like to convert to propane, I need to know which conversion kit to buy, and where. Thank you.

dyna glo natural gas heater Questions & Answers - Fixya

Parts for Dyna Glo, Thermoheat and Dyna Glo Pro Heaters

Propane Wall Heaters - Walmart.com

1352062 Dyna Glo Natural Gas conversion to LP Gas

When plugging in my reddy heater 110 it blows air & no heat and then goes off.

Comes on but cuts out and bellows smoke from filter.

I went online to get help with a Dyna Pro and paid 12.00 for some assistance on 1/13/11.I have not heard anything in response. It was having and E1 error and asked for help or product manual. I will call...

Dynaglo forced air kerosene heater fuel not getting to nozzle. replaced hoses, cleaned nozzle, cleaned fuel filter, pressure gauge reads OK.

I have an old master 150000 btu air forced portable heater. Everything has run fine until today. The kerosene level got low and it started sputtering. i unplugged the unit and filld with a1 kerosene. Now...

Why will the unit not even start? Before it quit it would puff a few times and then re light and then it wouldnt do anything. im stumped ive read a few things but nothing is makin sence

Heater starts and then runs a short while then stops but produces heavy cloud of smoke .. ignition is off ... model 55b

HAVE A 150,000 BTU REDDY HEATER, WITH COVER OFF IT WORKS FINE, WITH COVER ON T-STAT BLINKS ON DISPLAY AND AFTER ABOUT 5 SEC BLOWER CUTS OFF, HAS C3 ERROR CODE. IS THIS A THERMO PROBLEM

Not finding what you are looking for?

125000 BTU Kerosene Forced Air Heater with Thermostat

What does error code E1 on a tankless water heater mean?

Ask a Question

Top Protemp Heating & Cooling Experts

Paul Carew

john h

Brad Brown

Are you a Protemp Heating and Cooling Expert? Answer questions, earn points and help others

Manuals & User Guides

Related Topics:

Thermoheat dtu torpedo heater reads E1 error - Protemp 125000 BTU Kerosene Forced Air Heater with Thermostat

1 Answer

Donni Steen

Add Your Answer

Attachments: Added items

Related Questions:

What does error code E1 on a tankless water heater mean?

Troubleshooting EcoSmart Tankless Water Heater Error Codes

I have a dyna glo RMC 40 NGT vent less wall heater that I would like to convert to propane, I need to know which conversion kit to buy, and where. Thank you.

dyna glo natural gas heater Questions & Answers - Fixya

Parts for Dyna Glo, Thermoheat and Dyna Glo Pro Heaters

Propane Wall Heaters - Walmart.com

1352062 Dyna Glo Natural Gas conversion to LP Gas

When plugging in my reddy heater 110 it blows air & no heat and then goes off.

Comes on but cuts out and bellows smoke from filter.

I went online to get help with a Dyna Pro and paid 12.00 for some assistance on 1/13/11.I have not heard anything in response. It was having and E1 error and asked for help or product manual. I will call...

Dynaglo forced air kerosene heater fuel not getting to nozzle. replaced hoses, cleaned nozzle, cleaned fuel filter, pressure gauge reads OK.

I have an old master 150000 btu air forced portable heater. Everything has run fine until today. The kerosene level got low and it started sputtering. i unplugged the unit and filld with a1 kerosene. Now...

Why will the unit not even start? Before it quit it would puff a few times and then re light and then it wouldnt do anything. im stumped ive read a few things but nothing is makin sence

Heater starts and then runs a short while then stops but produces heavy cloud of smoke .. ignition is off ... model 55b

HAVE A 150,000 BTU REDDY HEATER, WITH COVER OFF IT WORKS FINE, WITH COVER ON T-STAT BLINKS ON DISPLAY AND AFTER ABOUT 5 SEC BLOWER CUTS OFF, HAS C3 ERROR CODE. IS THIS A THERMO PROBLEM

Not finding what you are looking for?

125000 BTU Kerosene Forced Air Heater with Thermostat

What does error code E1 on a tankless water heater mean?

Related Topics

Ask a Question

Popular Questions

Compressor makes noise and goes on and off constantly

My Sunbeam electric blanket controls

ERROR CODE ON AIRCONDITIONER LG ART COOL INVERTER MODEL NUMBER LSZ244VM4

Remove and relocate split air conditioner

Sunbeam Heating pad will not reset

Top Protemp Heating & Cooling Experts

Paul Carew

john h

Brad Brown

Are you a Protemp Heating and Cooling Expert? Answer questions, earn points and help others

Manuals & User Guides