Question about Kenmore 24 in. 15933 Built-in Dishwasher

1 Answer

How much jet dry should be put into the receptacle for it.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 218 Answers

Not sure of the capacity of the rinse agent reservoir, but it doesn't really matter. It will dispense the correct amount for each load of dishes. When refilling, just keep putting it in until it won't hold anymore.

Posted on Mar 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to Clear out dish soap from the jet dry resevoir?


Use a shop vac and suck it all out. Then, spray some Pam-type cooking spray grease into the jet dry reservoir and then, A) start a normal wash cycle and stop it a few minutes after it starts the spray action. Then, open the door and look for suds. B) If you see suds, spray them with Pam spray to knock them down and then C) cancel the wash to drain it out. Repeat ABC until all the suds are gone.

Then, whatever you do, DON'T put dish soap in the jet dry reservoir again!
:)

Good luck

Oct 21, 2014 | KitchenAid Dishwashers

1 Answer

I plugged in a spa/swimming pool motor/pump with water hooked to it as to not run it dry and it does not come on. Is it bad or how can I tell if it is bad. The motor is a GE. The pump unit is called ULTRA...


What did you plug it in to? Is it a cord or receptacle? Is there a reset button on the motor? Is the receptacle a GFI? Did you try to plug something else in there to see if it works? Check the breaker. You don't have to worry about running it dry, a couple seconds to test it won't hurt it. Most pool pumps are all plastic and they run for days dry, check it out.

Jun 08, 2010 | Home

1 Answer

I mistakenly put dish detergent in the jet dry dispenser. Now I have soap bubbles everywhere. How do I get it out?


the jet dry is in your door, you need to open it and clean it. open the door screws take the front panel off and get the jet dry unit out ... give me your model number i see how to open the unit and i will tell you.

Jan 23, 2010 | Whirlpool Dishwashers

1 Answer

We own a Bosch SHU5307UC dishwasher. Recently, during the 60 minute cycle, the foam builds up and at the end you can see all of it on the bottom. And the last minute dispaly stays on for a while. It...


the unit is over sudzing cut back on soap and dont clean dishes and then put them in dishwasher.dont use to much of the soap with jet dry. regular soap without jet dry in it then add and fill jet dry compartment

Dec 01, 2009 | Bosch SHU5307UC Built-in Dishwasher

1 Answer

WHERE DOES JET DRY GO


the turn nob is a cap that you screw out and pour your jet dry liquid in then replace the nob/cap the jet dry will be dispensed automatically.

Sep 29, 2009 | LG Dishwashers

1 Answer

Where do I put Jet Dry?


IF your dishwasher has the capability for using JetDry, you will ind that on the door there is a plug thing that you remove and fill and replace it. The plug usually unscrews a quarter turn and then pulls out.

Jul 25, 2009 | Magic Chef Dishwashers

1 Answer

Where do you put the jet dry?


ALONG SIDE THE POWDER DISPENSER- LIFT THE DOOR-

Jul 10, 2009 | Bosch 23 in. SHU3302UC Built-in Dishwasher

1 Answer

My jets wont turn on


All the electric power source to all jacuzzi tubs all required to be protected by a "ground fault" device. Have you noticed special wall receptacles in your kitchen and bathroom that have 'test' and 'reset' buttons? There may be a receptacle (or something that looks like a receptacle but without any slots for plugs) near the tub. Push the reset button. If the pump for the tub has an access panel, the device may be behind the panel. And last, the circuit breaker in the main electrical panel may be a ground fault type and needs reset there. Good Luck

Jul 09, 2009 | Whirlpool 5' Jacuzzi Tub Bathtub Cetra...

1 Answer

Washer < 1 year old. Jet dry will not go in


as ur machine is still under warrenty u should go in touch with GE and have thos problem solved free of charge....

Mar 15, 2009 | GE Monogram® ZBD6880NSS Stainless Steel...

1 Answer

Roper dishwasher model "wu3000v2"


Open the cover on the place where you put
the soap. There you should see a round piece that you turn and pull out fill the reservoir with jet dry. Once it's filled put the plug back in it should be good for 30 washes. Most have a sight glass that will turn from green when full and clear when empty jet dry will help.

Dec 31, 2007 | Dishwashers

Not finding what you are looking for?
Kenmore 24 in. 15933 Built-in Dishwasher Logo

Related Topics:

605 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

D. E. Hev

Level 3 Expert

1167 Answers

Fred Sops

Level 2 Expert

272 Answers

Cindy Wells

Level 3 Expert

4949 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...