Question about KitchenAid KUDS24SE Built-in Dishwasher

1 Answer

Door open light stays on when door shut.

The door light stays on when the door is shut and the buttons beep, but wont work. the light says door open.
model kudv24se

Posted by on

  • jayandlaurie Jan 27, 2009

    switch seems to work fine. I don't believe the problem is in the switch because the switch will turn off the light when I press it, but will come back on when I let go. It seem to work the opposite way.

  • jayandlaurie Jan 27, 2009

    NO THE MACHINE WONT WORK WHEN I HOLD THE SWITCH AND PRESS WASH. THE BUTTONS WILL ONLY BEEP WHEN THE DOOR OPEN BUTTON IS LIT UP. THE BUTTONS WILL ONLY BEEP THEY WONT DO ANYTHING ELSE. IF THE DOOR OPEN LITE GOES OUT WHEN I PRESS THE SWITCH THEN THE CONTROL PANEL WONT BEEP.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

Sounds like a faulty door switch not sensing that the door is shut. test the switches for continuity to determine the faulty switch

Posted on Jan 27, 2009

  • Travis Gray Jan 27, 2009

    does the machine function when you hold in on the switch and the light goes off

  • Travis Gray Jan 27, 2009

    it sounds like maybe the control is having an issue sensing the door switches. disconnect power and see if you can see any obvious damage on the control circuitry. good luck

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The green clean light wont go off when cycle is finished unless door is opened then shut again


Mark,
That is normal with most dishwashers. Mine at home does that.

Jun 12, 2015 | Dishwashers

1 Answer

Lights come on and it beeps when u select cycle but it wont run


Do you hear the water going in? If not, the float switch is probably stuck . From the inside you can see the cover usually on the front left corner on the floor of the dishwasher by the bottom rack. Remove the screw and float cover. The you see a small piece sticking up, gently push on it many time to try to free and clean it. This is actually pushing the float switch. Clean the plastic covers of soap gunk. Reassemble and try. The switch can be accessed from underneath if you want to replace it. Also a clogged or defective water valve will not allow water to enter.

Mar 24, 2014 | GE Dishwashers

1 Answer

Beeping won't stop at end of cycle


Our Bosch does the same thing, we just open the door shut of the power and close the door again so the heat can sanitize the dishes. I don't recall if there is an alert off button though.

Jan 08, 2014 | Bosch SHU9926UC Built-in Dishwasher

1 Answer

Zanussi zenb9950si


What is the beep for ? Temperature sensor ? Power sensor ? Door open sensor ?

Oct 30, 2013 | Zanussi & Electrolux Fridge Freezer Handle...

1 Answer

Service number kuds301xbl2


I would find the electrical breaker for this unit and shut it off for a minute, then re set the breaker thus resetting your unit.

Apr 28, 2013 | Maytag MDBH975AWS Stainless Steel...

1 Answer

First four lights on cycle indicator flash and machine beeps 10 times and then beeps every 30 seconds


I recomend checking drain hose for kinks or obstructions and checking drain pump. most dishwashers will drain first for about 25/30 seconds.Also check the drain hose into the main plumbing connection it maybe blocked.If it cant drain it wont do anything hope this helps.

Feb 17, 2012 | KitchenAid Dishwashers

1 Answer

My dishwasher from ikea renlig dw 60, is 6 month old and now the light to select the programs stay red all the time and pressing the selection button doesnt do anything. Thanks for your help


Similar just happened to us. Turned power off, waited a while, opened door. pressed and held power on button then pressed and held also the select button. Brought it back to life. End leds lit up and i could then select and worked when i shut the door. Ours is a smaller Renlig. Good luck.

May 27, 2011 | Dishwashers

1 Answer

Refridgerator E249T the beeping alarm wont stop. The door appears okay. How can I disconnect the alarm, please? Thanks Brian


I have the same fridge. It was driving me crazy. I emptied it. Cleaned it. Defrosted it. And was ready to dump it. Then worked it out. As it beeps when the door is open. How does it know. Because when the door is open the light is on. I taped up the light nob with masking tape, on top left of fridge. No light now
But no beep Yay!!!!

Jun 14, 2010 | Fisher and Paykel Fisher Paykel DD24DCB6...

1 Answer

The program light goes off and the BF162 doesn't start...


When you keep the button pressed for a few seconds the lights go off, this resets the dishwasher. Then press the p button again to the program you want 1st light is heavy soil 2nd light is normal soil, 3rd light is eco wash, 4th light is rinse. At the end of the cycle the program light you have selected will flash.

Apr 24, 2009 | Hotpoint 23 in. BFI62 Built-in Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Carmen Mikulic

Level 2 Expert

409 Answers

Are you a KitchenAid Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...