Question about KitchenAid Dishwashers
The Clean light blinks 4 times and this continues. I have reset the power with no luck.
Proper reset sequence for this model is to push any three buttons on the panel, one after the other, three times in succession, as in heavy duty-normal-light/china-heavy duty-normal-light/china-heavy duty-normal-light/china. All lights on the panel should then illuminate
Posted on Feb 19, 2016
All the lights are illuminated. What are the next steps?
Thank you! Thank you! Thank you!
with my kitchenaid kdte234, I pushed the three buttons of Options in sequence. All lights on!
Have a dishwasher kitchenaid
Type 577-0 Mod KUDC20CVSS4 with all the lights blinking... cannot reset with those sequences...
×
Press High Temp Scrub and Dry Heat option buttons in quick succession one after the other for about 6 sec until all the lights come on. Then press Cancel button. This should reset the dishwasher. Press equivalent buttons on the panel if the actual ones above are not there.
Make sure the dishwasher detergent dispenser lid is shut and the dishwasher door is shut before you start the above reset sequence.
Posted on Jan 02, 2013
I am not able to close the door and push the buttons. Here are the buttons that are on the top of the door: Pro Wash, Heavy Duty, Normal Wash, Light/China, 1 Hour Wash, Rinsh Only, Pro Scrub, Hi-Temp Wash, Sani Rinse, Top Rack Only, Pro Dry, 4 Hour delay, Start/Resume and Cancel/Drain.
please clarify the reason if any for not being able to close the door. The buttons to press for the reset in your case would be Hi-Temp Wash and Pro Dry. Maybe you can try to run the reset sequence as explained in my old post with the door open and see if it works. When all the lights light up on the panel press cancel.
I tried the high temp scrub and pro dry without success. The touch buttons are on the inside top of the door and when you close the door, you can't get to the touch buttons.
I got the dishwasher pulled slightly out so I can close the door and touch the two buttons you mentioned. This did not reset the machine.
The sequence is High Temp/ Dry/ High Temp/ Dry for about 6-8 sec. If you are unable to reset the dishwasher, and looking at the fault light you mention, the heater unit is failing and will need to be attended to by a repair technician.
How do you reset a K'Aid KUDS03CTBL3?
×
If the clean light flashes 7 times, pauses then repeats...
If the dishwasher doesn't sense a water temperature increase, it will
stop working and lock the functions (clean light flashes 7 times, all
buttons are non responsive).
To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...
-high temp wash
-heated dry
-high temp wash
-heated dry
...all
the lights will turn on briefly and the machine will start a diagnostic
cycle. You can press cancel or let the diagnostic cyle finish (1-2
minutes).
You should now be able to run the dishwasher as normal.
If
the issue returns, you could have a problem with the heating circuit
(ie. element, thermostat or wiring). It rarely happens but it could
also be the door switch not engaging properly when the door is closed
(slightly bend the door latch down making sure it doesn't hit the door
when you close it).
Posted on Feb 20, 2009
SOURCE: KItchen Aid Dishwasher KUDI01FL Stopped Running and Will not Start
try the reset button sequence i posted in the other question..
Posted on Jan 24, 2009
Hello & Welcome to FixYa
Flashing
clean light is reset by pressing two buttons in sequence 3-4 times, to reset
your kenmore press these buttons in sequence:
High
temp wash-heated dry-high temp wash-heated dry
Please
get back to me if you have any other questions.
Kevin
24,702 views
Usually answered in minutes!
×