Looking for the serpentine belt diagram for a 1999 chevrolet malibu 3.1 l

Question edited for clarity.
Question moved to model category.

Lots of diagrams especially on the images tab.

https://www.google.com/search?q=2012+chevy+malibu+serpentine+belt+diagram

..

google 2013 chevy malibu 2.4 eco serpentine belt diagram
should be diagram under hood.
https://www.cargurus.com/Cars/Discussion-c23264_ds1151168

https://www.manualslib.com/manual/877888/Chevrolet-2013-Malibu.html?page=392

Check here...

https://www.fixya.com/cars/t29813866-need_serpentine_belt_diagram_one_page

and sites here.....

https://www.google.com/search?q=2009+chevrolet+malibu+3.6l+v6+engine+serpentine+belt+diagram

Best to you

Search Results

images for diagram on how to replace a serpentine
How To Install Replace Serpentine Belt Oldsmobile Alero 99 ...? 3:33https://www.youtube.com/watch?v=jkzXTt43uwwFeb 9, 2012 - Uploaded by 1A Auto PartsHow To Install Replace Serpentine Belt Oldsmobile Alero 99-04 2.4L .... There should be a belt routing diagram on the frame rail or under side ...serpentine belt install 3.1/ 3.4 v6 - YouTube? 4:00https://www.youtube.com/watch?v=GYoWuvEZ2DcMay 6, 2013 - Uploaded by JoeTheAutoGuythis a serpentine belt install video on a 3.1 liter gm v6 , 3.4 liters are the same in ... Replacing the alternator or serpentine on anyOldsmobile Alero 99-04 3.4 Liter ... Serpentine Belt Replacement 1995-2005 Chevrolet Cavalier .

Make sure that the belt is fully seated in ALL pulleys, if it still slips off, then you have a pully that is bent, or out of alignment.

There are 2 possible diagrams for your car depending on which engine it has. Both diagrams are listed below:


1999 Chevy Malibu 2.4L






1999 Chevy Malibu 3.1L

If you open the hood and look on the frame (usually just near the hood latch) there should be a diagram there for you. It might also be on the underside of the hood itself.

Well you don't have to remove the tensioner. If you look at it, you'll see a 3/8 square hole in the arm of the tensioner. Put a ratchet wrench, or breaker bar in the hole, and you can move the tensioner, it is only spring loaded. The diagram for how the belt laces in should be on the radiator core support. Lace it for the majority around, move the tensioner, and once you have the belt in line, release the tension on the tensioner arm.

CLICK on the following LINK. It has the Serpentine Diagrams you will need.

The standard rule to removal the Serpentine Belt:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Rotate/Move the Tensioner away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/2000/make/chevrolet/model/malibu/2000_chevrolet_malibu_drive_belt_routing_diagram.htm

1999 chevy malibu 6 cyl dosen't have a timing belt just the serpentine drive belt the routing diagram should be under the hood