Question about 2005 Peugeot 307 1.6

1 Answer

How i can fix the problem off code p2299 in my vehicle

I already changed the accelerate paled

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Peugeot Master
  • 937 Answers

That is a bad or improper brake or accelerator pedal signal. You must determint which of the 2 is the problem and either replace the switch or troubleshoot to determine if the wires have been disconnected.

Good Luck!

Posted on Nov 25, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My car does not accelerate and it does not even reach 20km/h and also the sound of the motor does not change while noting happen

From what you have described the computer has set the vehicle into limp mode because there is a major problem. You no doubt have a check engine light displaying and if not some other warning lights displaying.

You need to get the vehicle to a reputable mechanic (preferably one familiar with your vehicle brand/model) so he can run a scan to check what fault codes the vehicle computer is generating because there will be a number of them... From there the issues can be investigated and the causes of the fault codes identified and fixed.

Apr 10, 2016 | 2006 SsangYong Rexton 270

2 Answers

Cruisecontrol notworkn lite don't even comeon also 4xlight keeps blkn whn n 4xit use 2 stay on whn n use code 2299shown would the codehave sthing todo with the cruisecontrol not wkn or thy different?

What make vehicle ? OBD2 Code P2299 Preventative Auto Service 4x4 light blink indicates a problem in the system an more then likely there is a DTC - diagnostic trouble code stored in the 4x4 control module .The 4X4 module is different then PCM , a code reader will not check codes in 4X4 system , need a professional scan tool .
OBD2 Code P2299: Brake Pedal Position / Accelerator Pedal Position Incompatible, this would cause the cruise control not to work .

Feb 02, 2016 | Cars & Trucks

1 Answer


when you post a code please give symptoms of the operation of the car.. I dont do just codes ..I go by whats actually going on with the vehicle..

Dec 25, 2013 | Chrysler Cars & Trucks

1 Answer

Citroen c5 code p2299

Brake Pedal Position
/ Accelerator Pedal Position Incompatible

Jun 10, 2013 | Citroen Cars & Trucks

1 Answer

2001 Subaru Forestor Won't Accelerate

MAP SENSOR will do this exact thing.... Some vehiles you have to clear the codes and allow the vehicle to RELEARN...

TPS (Throttle Position Sensor) that is failing will also do this same thing

Apr 08, 2013 | 2001 Subaru Forester

1 Answer

The change oil soon light comes on for about 15 minutes then goes out. The oil has already been changed. How do I fix this??

The Reset Procedure Is:
With The Ignition Key In The "on" Position, but The Engine Off, Fully Push And Release The Accelerator Pedal Slowly 3 Times Within 5 Seconds. If The "change Oil" Light Flashes, The System Is Resetting. Turn The Key Off, Then Start The Vehicle.
If The "change Oil" Light Comes Back On, The Light Has Not Reset. Repeat The Procedure.

Sep 29, 2012 | 1998 Pontiac Grand Prix

1 Answer

Rover 75 vehicle starts but will not have acceleration

Hi, Check fuel filter and replace. Check and replace sparkplugs. Check ignition components. coil, wires, distributor for cracks. and then check for codes. Good luck.

Dec 22, 2011 | Cars & Trucks

2 Answers

I have these codes coming up on my 2005 Dodge Ram. 5.7 liter motor: P0406 P2096 P0137 P2299 Thank you.

code #0406 = egr position sensor circuit high ( stuck egr valve or bad egr sensor most likely sensor )

code #2096 = downstream fuel trim system lean ( see next code )

code #0137 = O2 sensor bank 1 sensor 2 circuit low ( replace rear O2 sensor driver side )

code #2299 = brake peddle position/accelerator pedal position incompatible. ( hav you been power braking this truck? ) ( brake light was on wile accelerator was being pushed )

Mar 17, 2011 | 2005 Dodge Ram

1 Answer

Diagnostic code P2299 for 2004 Dodge Ram 1500 5.7 hemi?


Set Condition:
The PCM recognizes a brake application following the APPS showing a fixed pedal opening. Temporary or permanent. Internally the PCM will reduce throttle opening below driver demand. One trip fault and the code will be set within 5 seconds. ETC light will illuminate, the light will only stay illuminated while DTC is active.

Possible Causes




The most likely cause of this DTC is Brake Torquing the engine by pressing the Accelerator pedal and the pressing the Brake Pedal.

Jul 17, 2008 | 2004 Dodge Ram 1500

Not finding what you are looking for?
2005 Peugeot 307 1.6 Logo

239 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

mike hayward

Level 2 Expert

279 Answers

lloyd cole

Level 2 Expert

250 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides