1998 honda accord ex 3.0 vtec cluster temp don't work? How can I fix it?

92-00 Honda Engine Swap Wiring Guide VTEC AND NON ...

honda-tech.com/.../92-00-honda-engine-swap-wiring-guide-vtec-non-vt...
Oct 8, 2011 - 92-00 Swap Wiring Guide for VTEC and Non-VTEC ... try to compile one thread that would try to answer pretty much 95% of all questions ... I wanted to do this because often times I end up posting the same thing to ... to ECU harness so using an EX/SI 92-95 engine harness will make VTEC plug and play.

97 accord non VTEC to VTEC ' HondaSwap

hondaswap.com > Model Specific > Accord
Jan 16, 2010 - 15 posts - ‎6 authors The distributors may be different on the vtec/non vtec. .... As was previously stated, allyou need to do is add wiring for VTEC. ... that connect to the ecu to the connectorsthat wire in your engine harness while the engine is out... f22b2 non vetec swap to f22b vtec need help asap
3 posts
Sep 22, 2012
96 accord head swap non vtec to vtec
10 posts
Jun 1, 2012
1990 USDM CRX Si D16A6 to ZC SOHC non-VTEC ...
20 posts
Mar 7, 2012
99 Accord non-vtec to vtec engine swap, need help
5 posts
Sep 27, 2011
More results from hondaswap.com

It is the wire close to the VTEC valve solenoid plug be cut off. Sounds wired, but it happened to my 2001 accord EX V6 sedan. After I solder it back, the TCS light turned off. But I had to disconnect the battery for 5 minutes and put it back to reset the Check Engine light.

need to pull the ABS codes to see where the problems are.

For the 1998 Honda Civic 1.6L SOHC -In-Line 4-Cylinder:
For all: LX, DX, EX, GX and HX Models; VTEC and VTEC-E

Firing Order:
1-3-4-2

Cylinders:
...........(back)..........
|...4.....3....2....1...|
...........(front)

Distributor:
....(back)
..........1
2
........o
.................3
.....4
.....(front)
Rotation: Clockwise
Let me know if this helped, or if you have addtional questions. Feel Free to contact me at FixYa.com!

p1259 is vtec system fail. check your oil level and condition. will prob need a vtec sol and filter and poss the vtec pressure switch.

I have a 1998 Honda Accord EX. I had the check engine light come on as well and I had the code read by PepBoys. The code was:P1259 or VTEC SYSTEM Malfunction.
I Don't know jack about were to start to fix this problem, so I bit the bullet and took the car to my Honda Dealer. The problem was checked out and was told this.
( REPLACE VTEC VALVE ASSEMBLY)
I had them do the work because I dont know how to do this. So after $204.00 in Labor and $162.29 in parts, for a grand total $366.29, The car was fixed!!!!!!! Run's great and no check engine light on anymore. So to help you out as best I can, here is the numbers that are on my work sheet. I dont know witch numbers represent the part number but this is how it looks on my paper.

1 15810-PAA-A02 8108797-90870 VALVE ASSY, SPOOL $150.75

1 15825-P0A-015 8161598-15999 FILTER, SPOOL VALVE $11.54

There you go! I hope this gives everyone a place to start. maybe get your self a Haynes Repair Manual (#42014 is for the 1998-2002 Honda Accord, all models) and try to do the work your self. Good luck to all of you form Donald M. in SoCal.

1.1 o2s(ho2s)(s1) = eng
3.2 map circuit = high input eng
7.1 t p sensor(a) = voltage low eng

Right beloww throttle body toward front of car

If you are talking about just plugging into the speed sensor yes. A VTEC and NON-VTEC are one and the same.