I need to find the junction box labeling for the relays

In a 2006 Ford Territory, the turn signal relay is located in the central junction box, also known as the fuse box. Here's how you can locate and access the relay:

1. Find the central junction box: The central junction box in the Ford Territory is typically located under the dashboard on the driver's side. It is usually positioned towards the lower part of the dashboard, near the pedals.
2. Remove the cover: Once you've located the central junction box, you'll need to remove the cover to access the relays and fuses inside. The cover may have clips or screws holding it in place. Use a flathead screwdriver or the appropriate tool to remove any screws or release the clips to detach the cover.
3. Locate the turn signal relay: Inside the central junction box, you'll find a grid or diagram that indicates the different relays and fuses. Look for the turn signal relay, which is often labeled with its specific function or identified by a symbol representing the turn signals. Refer to the owner's manual or the diagram inside the junction box for the exact location of the turn signal relay.
4. Replace or test the relay: If you're experiencing issues with the indicator sound, you can try replacing the turn signal relay with a new one. Alternatively, you can test the relay using a multimeter or consult a professional mechanic to diagnose the problem accurately.

Remember to disconnect the car's battery before working on the electrical components to prevent any electrical mishaps. If you're uncertain about locating or handling the relay, it's recommended to consult a qualified mechanic or refer to the vehicle's service manual for detailed instructions specific to your 2006 Ford Territory model.

The fuel pump drive module is typically located in the central junction box, which is located under the driver's side of the dashboard. To access the fuel pump drive module, you will need to remove the panel covering the central junction box.
Here is a general guide for finding the fuel pump drive module in a 2003 Navigator:

1. Locate the central junction box: The central junction box is usually located under the driver's side of the dashboard, near the steering column.
2. Remove the panel: The panel covering the central junction box is usually held in place with a few screws. Use a screwdriver to remove the screws and carefully lift off the panel.
3. Locate the fuel pump drive module: The fuel pump drive module will be a small electrical component with a series of wires connected to it. It may be labeled as the "fuel pump relay" or something similar.

If you are having trouble finding the fuel pump drive module, you may want to consult your owner's manual or a repair manual for specific instructions. Alternatively, you can try searching online for a diagram or video that shows the location of the fuel pump drive module in a 2003 Navigator.

Sorry but it is non - serviceable , location smart junction box ! If the relay were bad you would need to replace the smart junction box . Is the air bag light lit ! ( possible clock spring )
Inspection and Verification

1. Verify the customer concern.

1. Visually inspect the following for obvious signs of mechanical or electrical damage.

Visual Inspection Chart Mechanical Electrical

• Horn
• Horn switch (part of the steering wheel)

• Battery junction box (BJB) fuse 2 (50A)
• Smart junction box (SJB) fuse 14 (20A)
• Circuitry
• Clockspring
• BJB
• SJB

Symptom Chart Condition Possible Sources Action

• The horn is inoperative

• Fuse
• Circuitry
• Steering wheel switch harness
• Horn
• Clockspring
• Horn switch (part of the steering wheel)
• Smart junction box (SJB)

• Go To Pinpoint Test A .

Central junction box fuse # 18 an it is 15amp !
Central Junction Box Behind LH side of I/P If the fuse is good there are three relays , all unlock relay an all lock relay an driver door relay in the . relay box !
Relay Box
Behind I/P, right of steering column Visual Inspection Chart Mechanical Electrical

• Power door lock actuators
• Power door lock switches

• Fuse junction panel fuse 18 (15A)
• Circuitry
• Damaged or corroded connectors
• Faulty or sticking relays

None of the doors lock or unlock ?

Fuse/Relay Location: 24
Fuse Amp Rating: 20A
Passenger Compartment Fuse Panel Description: Horn Relay Feed

http://www.fordservicecontent.com/Ford_Content/catalog/owner_guides/08f23og1e.pdf

1 circuit breaker and 2 fuses
Circuit Breaker #601--30Amp--in Battery Junction Box
Fuse 103--50Amp--in Battery Junction Box
Fuse 14--15Amp--in Central junction box
Multiple Relays and Modules Involved--if circuit breaker and both fuses good, diagnostic scanner use indicated.

Is the air bag light lit on the instrument cluster ? The horn relay isn't under the hood in the engine compartment , it's in the SJB - smart junction box located inside the passager compartment . Under the dash panel left side . You can take the relay back to autozone because it's not the right one ! The relay is inside the smart junction box ,soldered to the printed circuit board !
Horn Horn
The vehicle is equipped with dual horns. The horns are mounted in the LF frame rail corner behind the front bumper.
The horn system consists of the following components:

• steering wheel horn switches
• clockspring
• horns
• smart junction box (SJB)

Horn Switch, Steering Wheel Mounted
The horn switches are incorporated within the driver side air bag module in the steering wheel. The switches are grounded and control the horns through the clockspring. For removal and installation of the driver side air bag module, refer to Section 501-20B .
Visual Inspection Chart Mechanical Electrical

• Horn
• Horn switch

• Battery junction box (BJB) fuse 1 (60A)
• Smart junction box (SJB) fuse 38 (15A).
• Circuitry
• Speed control actuator
• Clockspring
• SJB

Smart Junction Box (SJB) Diagnostic Trouble Code (DTC) Index
DTC Description Source Action B1217 Horn relay coil circuit failure Smart junction box (SJB) If the horn is inoperative, Go To Pinpoint Test A . If horns sound continuously, Go To Pinpoint Test B . B1218 Horn relay coil circuit short to battery Smart junction box (SJB) Go To Pinpoint Test A .
Any codes ?
Symptom Chart NOTE: Refer to Wiring Diagrams for connector numbers stated in the pinpoint test. Condition Possible Sources Action

• The horn is inoperative

• Battery junction box (BJB) fuse 1 (60A).
• Smart junction box (SJB) fuse 38 (15A).
• Circuitry.
• SJB.
• Horn switch.
• Horn.
• Speed control actuator.

• Go To Pinpoint Test A .

Your best bet , take it to a qualified ford service center .

The autolamp system, controlled by the vehicle security module, supplies voltage to the same circuits used by the headlamp switch to power the exterior lamps when low light conditions are detected.
Anyone else have or have fixed this problem some help please???? What fixed someone else's vehicle probably won't fix your's .Electronic's involved . Using service repair info. , wiring diagram's an testing the electrical circuits is how professional Technician's fix electrical system problems , not guessing or looking for magical fixes on web sites or forum's.
Visual Inspection Chart Mechanical Electrical

• Headlamp switch

• Battery junction box (BJB) fuses:
  • 1 (60A)
  • 16 (15A)
  • 22 (20A)
• Central junction box (CJB) fuse 20 (5A)
• Circuitry
• Photocell sensor
• Vehicle security module

Plus hooking up a factory scan tool an checking for DTC'S - diagnostic trouble code's .
Vehicle Security Module Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1695 Autolamp On Circuit Failure Vehicle Security Module Go To Pinpoint Test J . B1792 Autolamp Sensor Input Circuit Short to Battery or Open Vehicle Security Module Go To Pinpoint Test J . B1793 Autolamp Sensor Input Circuit Short to Ground Vehicle Security Module Go To Pinpoint Test J . B2661 Parklamp Relay Output Short to Vbatt Vehicle Security Module Go To Pinpoint Test R . B2662 Parklamp Relay Output Open Circuit Vehicle Security Module Go To Pinpoint Test I . B2663 Headlamp Relay Output Short to Vbatt Vehicle Security Module Go To Pinpoint Test F . B2664 Headlamp Relay Output Open Circuit or Short to Vbatt Vehicle Security Module Go To Pinpoint Test H . Symptom Chart Condition Possible Sources Action

• No communication with the vehicle security module

• Circuitry.
• Vehicle security module.

• REFER to Section 418-00 .

• The autolamps are inoperative

• Circuitry.
• Headlamp switch.
• Photocell sensor.
• Vehicle security module.

• Go To Pinpoint Test G .

Electric Testing Techniques You Need to Know

You can find the information in your owner's manual or you might need a repair manual. Both of those may be available for trouble shooting on the website of the auto maker. Google Dodge and see if you can.

The fuses may be in a box close to the floor under the dash. Another likely place is under the bonnet. There will be a label that tells you what is inside the box.
Jim Hart

The dealer can hook up his diagnostic tool and retrieve the fault code. -------------- SECTION 413-06: Horn 2003 Expedition/Navigator Workshop Manual DESCRIPTION AND OPERATION Horn Horn components include the following items:

• clockspring
• horn relay
• horns
• steering wheel pad horn switch

Horn switches The horn switch is incorporated into the driver side air bag module in the steering wheel. The switch is powered through the clockspring and grounded through the steering column. For removal and installation of the horn switch, refer to Section 501-20B .
Horn relay The horn relay is incorperated into the central junction box (CJB). The central junction box is located behind the passenger lower kick panel.
------------------------------------------------------------
Symptom Chart
Symptom Chart Condition Possible Sources Action

• The horn does not sound

• Central junction box (CJB).
• CJB fuse 26 (20A).
• Circuitry.
• Horn switch.
• Horn.
• Clockspring.
• Powertrain control module (PCM).

• Go To Pinpoint Test A .

• The horn sounds continuously

• Central junction box (CJB).
• Circuitry.
• Horn switch.
• Horn.
• Vehicle security module.
• Tire pressure monitor (TPM) module.
• Clockspring

• Go To Pinpoint Test B .