2006 chev malibu p0446 code

P0446 Evaporative Emission Control System Vent Control Circuit Malfunction

Why in the world would you replace the canister when the problem is in the vent circuit?

http://ricksfreeautorepairadvice.com/evaporative-emissions-system-primer/

P0446 Evaporative Emission Control System Vent Control Circuit Malfunction. The code P0446 is set when the engine computer recognizes a fault or restriction at the vent control part of the Evaporative emission control system (EVAP).

https://www.obd-codes.com/p0446

Evaporative Emission Control System Vent Control Circuit Malfunction

the following links can assist you with problem
https://www.obd-codes.com/p0446 P0446 OBD II Trouble Code p0446 Yahoo Video Search Results

code p0446 refers to evaporative emission (EVAP) system-vent control-circuit malfunction===causes --wiring--EVAP canister purge valve--ECM
code p0455 refers to EVAP system-large leak detected===causes --hose connections--intake leak--EVAP canister---EVap canister purge valve
code p0172 refers to system too rich, bank 1===causes intake blocked---EVAP canister purge valve--fuel pressure ---EGR system---injector/s ---ECM
because the EVAP purge valve appears in all codes I would be inclined to change that unit first the run the fault codes again

P0446 Evaporative Emission Control System Vent Control Circuit Malfunction The code P0446 is set when the engine computer recognizes a fault or restriction at the vent control part of the Evaporative emission control system (EVAP). The description of the fault varies between different car manufacturers, but one thing is common, the code P0446 doesn't directly point to a defective part; some testing might be required to pinpoint the faulty component. What can cause the code P0446: - faulty vent control valve - blockage at the vent hose, vent filter or vent control valve - open or short in the vent control valve circuit - bad charcoal canister - EVAP system leak - faulty EVAP system pressure sensor - bad vacuum switching valve (VSV) - stuck open purge valve (solenoid)

DTC P0446 - Evaporative Emission Control System Vent Control Circuit Malfunction
Evap vent valve has only one purpose. It closes in order to seal the vent so the EVAP system can pressurize and ensure there are no leaks. Evap vent valve is usually supplied Batt. voltage with key on. The ECM's driver controls the ground, and when grounded, activates the valve (closing it). If the ECM detects a short to ground, and open,or a short to battery voltage on the control circuit, P0446 will set. Code also may refer to ECM detecting that EVAP system is unable to achieve or maintain vacuum during test. There will be no obvious symptoms to driver, other than MIL illumination.

A code P0446 could mean one or more of the following has happened:
Faulty vent valve
Open, short or excessive resistance on Vent valve control circuit
Blockage of vent valve
Bad PCM


With a P0446 OBD-II trouble code, here are some things to try:
Replace Vent valve
Repair open, short, or resistance problem in control circuit
Repair open, or short, or resistance problem in power circuit
Replace PCM


Hope this helps (remember to rating this free answer and leave us some testimonial comment).

Hi, your vent valve has malfuntioned. The vent valve is near the tank, and has a hose to the tank and a solenoid to close it. Check the wiring/connector. If OK, try applying 12 volts directly to the solenoid. If it does not click when voltage is applied, replace the solenoid/valve.

P0446 Evaporative Emmission Control System Vent Control Circuit OBD-II Trouble Code Technical Description

Evaporative Emission Control System Vent Control Circuit Malfunction
What does that mean? Evap vent valve has only one purpose. It closes in order to seal the vent so the EVAP system can pressurize and ensure there are no leaks. Evap vent valve is usually supplied Batt. voltage with key on. The ECM's driver controls the ground, and when grounded, activates the valve (closing it). If the ECM detects a short to ground, and open,or a short to battery voltage on the control circuit, P0446 will set. Code also may refer to ECM detecting that EVAP system is unable to achieve or maintain vacuum during test.
Symptoms There will be no obvious symptoms to driver, other than MIL illumination.
Causes A code P0446 could mean one or more of the following has happened:

• Faulty vent valve
• Open, short or excessive resistance on Vent valve control circuit
• Blockage of vent valve
• Bad PCM

Possible Solutions With a P0446 OBD-II trouble code, here are some things to try:

• Replace Vent valve
• Repair open, short, or resistance problem in control circuit
• Repair open, or short, or resistance problem in power circuit
• Replace PCM

P0446....Evaporative Emission Control System Vent Control Circuit

this vehicle should not have failed with this code ,its a rubber pipe perished or split ,short answer ice road truckers is back on after adverts sorry

P0446 Evaporative Emission System Vent Control Circuit.
The following are descriptions of all Evaporative possible codes:

P0441 Evaporative Emission System Incorrect Purge Flow
P0442 Evaporative Emission System Leak Detected (small leak)
P0443 Evaporative Emission System Purge Control Valve Circuit
P0444 Evaporative Emission System Purge Control Valve Circuit Open
P0445 Evaporative Emission System Purge Control Valve Circuit Shorted
P0446 Evaporative Emission System Vent Control Circuit
P0447 Evaporative Emission System Vent Control Circuit Open
P0448 Evaporative Emission System Vent Control Circuit Shorted
P0449 Evaporative Emission System Vent Valve/Solenoid Circuit
P0450 Evaporative Emission System Pressure Sensor/Switch
P0451 Evaporative Emission System Pressure Sensor/Switch Range/Performance
P0452 Evaporative Emission System Pressure Sensor/Switch Low
P0453 Evaporative Emission System Pressure Sensor/Switch High
P0454 Evaporative Emission System Pressure Sensor/Switch Intermittent
P0455 Evaporative Emission System Leak Detected (large leak)
P0456 Evaporative Emission System Leak Detected (very small leak)
P0457 Evaporative Emission System Leak Detected (fuel cap loose/off)
P0458 Evaporative Emission System Purge Control Valve Circuit Low
P0459 Evaporative Emission System Purge Control Valve Circuit High
---
At least the cap isn't loose for the gas tank.

I would clear the code with an OBD-II Scanner 'erase code' button, and see how long it takes for it to come back.

P0446 Evaporative Emission Control System Vent Control Circuit Malfunction

The evaporative emission control system checks to make sure there are no leaks in the lines that run from the gas tank to the charcoal canister and up to the engine. It also checks to make sure the gas cap is sealing correctly.
It may just be that the cap was not on tight and the code was tripped.

A dusty environment can also clog the vent line and cause this code.
Have the code cleared and see if it comes back. Some auto parts stores like Auto Zone can read and clear the codes for you.
Hope this helps.