Question about 2007 Peugeot 207 CC

Open Question

Re-programing peugeot 207 key fob after battery change

Remote ouyjhn key fob wont work have to lock and unlock the car using the key

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 205 Answers

SOURCE: fob wont work the locks

I have done this procedure for my peugeot 307, but you can give it a try for your Pug expert and let me know if it works.
Disconnect the battery for 5 minutes then after connecting the battery perform the following steps
1. Turn the Ignition switch to the ON position using your key.
2. Press the LOCK button for 10 seconds. It will set your ECU in programming mode.
3. Remove the key and wait for 10 seconds.
4. Press the buttons on the key repetedly for operation (lock und unlock doors) to synchronise the key signals.
5. Again turn the ignition on and start the engine.
6. Turn the ignition OFF

If fails in step 4, then disconnect the battery and reconnect it and wait about 10 minutes to check the remote. Some new ecu units synchronises itselfs if you disconnect the battery while in programiing mode.

Posted on Jun 13, 2009

Ad
  • 1 Answer

SOURCE: key fob wont work on my Peugeot Expert

Try this, press and hold the large button on your key fob,after 20 seconds press the small button while still pressing the large one, the led light will go out and will reset your remote. It worked for me. ray1297

Posted on Oct 23, 2009

Danniboi
  • 1098 Answers

SOURCE: my dashboard lights come on after i have switch

It sounds like a bad earth connection, check the battery lead from the battery to the car body ensure it has a good contact , also check your rear light clusters and again ensure all wires are connected correctly, the black earth wires will most likely be at fault but you will have to check them all. there is one to the gearbox from the loom one from the battery to the the car body and another in the boot from the rear light clusters, also one on the back of the car radio. I would say its touching wires or a bad earth somewhere, also look around the fuse box especially the back of it.

Hope this helps
Regards
Dan

Posted on Feb 05, 2010

  • 1 Answer

SOURCE: i need to reset my peugeot 406 key fob

Had same trouble with my 406, fixing no problem, with new battery in fob, insert into ignition, turn key, BUT DO NOT START ENGINE, hold button for about 10 seconds release button and remove key from ignition, then try and see if doors lock on remote, if not try again, had to do this a couple of times, and it worked, sorry to say that now my key fob button has completely fell apart, through ware and tare

Posted on Feb 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2012 kia optima Fob died i replaced the battery but it still wont work unless i put it in the glovebox just to start the car the buttons on the fob doesnt work i only had the car for 2 months.


There is a possibility that your key fob might lost the programming. I suggest that you re-program your key fob, follow the next steps to re-program it.

Instructions
    • 1 Sit in the vehicle and close all the doors. Insert the key into the ignition.
    • 2 Turn the key to the "Off" position then to the "On" position. Repeat this until the door locks cycle to indicate that the programming mode is activated. End with the ignition key in the "On" position.
    • 3 Press the "Unlock" or "Lock" button on the programmable remote. Listen for the doors to lock or unlock to verify successful programming.
    • 4 Turn the ignition key to the "Off" position. Listen for the door locks to cycle to indicate that you have exited the programming mode.
    • 5 Repeat the above steps to add any additional remotes.


Read more : http://www.ehow.com/how_7446180_program-key-fob-kia-optima.html

May 31, 2015 | Kia Optima Cars & Trucks

1 Answer

Security Lock Flashing. Even when I lock with key it stops flashing but stays on. What is solution?


You are going to have to use the Key fob or remote alarm fob to go threw a set of lock and unlock procedure. Crank the car shut it off remove the key outside the vehicle at a distance of at least 30ft then lock the car, wait till it arms and the dash light blinks once this is active you want to unlock the car with the remote. If this one does not work do the same thing except when you unlock it do so with the key to re open after arming security.Also make sure you have both fobs or all remote fobs with you when you do this lock with one unlock with the other then vise, versa ok if you need any further help just ask also make sure your battery is fully charged and the terminals are clean this will affect a security system bad a low battery or low battery in the FOB's.

Apr 23, 2015 | 2012 Toyota Camry

1 Answer

Mustang alarm


Ford sold a Ford branded alarm through the parts department. These sometimes were a dealer installed option on new cars. Mine would randomly stop responding to the remote and I would have the same symptoms as you describe. I had it removed and the original equipment factory system still worked. Be warned, if you have the Ford "accessory" alarm, your key fobs (remotes) are different and the method to program them is different from what you will read online. You can tell if you have the system by looking at your key fob. The standard Mustang key fob is a 4 button (lock, unlock, panic, and trunk). The accessory alarm uses a 3 button remote and clicking unlock twice would pop the trunk. I really wish I had a picture of the remote because there are 3 button Ford key fobs for cars without a trunk release although I don't think you should have one on a Mustang. Long story short, if you have the accessory alarm, you can solve your problem by having it removed but you will need new 4 button key fobs to remotely lock/unlock your doors

Apr 04, 2014 | 2003 Ford Mustang

1 Answer

Vehicle wont start


what type of vehicle?

Jun 06, 2012 | Cars & Trucks

2 Answers

My alarm wont turn off. my car wont start. its a 2004 tiburon.


With alarm activated your ignition is disabled.Find the combination to disable it.With GM's you hold opposing buttons on the fob till it beeps twice. The dealer should help for no charge.

Feb 28, 2010 | 2004 Hyundai Tiburon

1 Answer

Key locked in 2001 pontiac grand prix battery is


lock smith or someone authorized to use a slimjim[can do more damage if dont know how to use ]--or-- key fob wont work if vehicle battery dead if u can reach up under car at front and release hood latch then jump battery and then use key fob to unlock door

Feb 20, 2010 | 2001 Pontiac Grand Prix

3 Answers

My Porsche Key fob no longer unlocks the doors


Insert key into door barrel or ignition lock and turn key, whilst doing this press the unlock/lock button, the led on the dash should flash to indicate this has initialised the key to the car, then remove key and test operation of remote. If this fails then a new remote plus coding to the car by your dealership is needed

Feb 16, 2010 | 2005 Porsche 911

1 Answer

Need to reset the key fob after replacing the battery


You should not have to reset the key fob after a battery replacement. The signal from the key fob stays the same and is programed to the reciever.
If the key fob needs to be reprogrammed then follow these steps.
1. Have all key fobs with you during programming.
2. Sit in the vehicle with all doors closed.
3. Lock all doors using the Lock/Unlock switch on the door.
4. Insert and withdraw the ignition key 7 to 9 times within 10 seconds (do not turn the key, just insert and withdraw).
5. The 4 way flasher indicator on the dash should flash once or twice.
6. Insert the ignition key and turn it on (key on, engine off).
7. Press any button on one remote and the 4 way flasher indicator on the dash should flash once.
8. If you have more key fobs to program use the Lock/Unlock button on the door to unlock the doors and then lock the doors.
9. Press any button on the next key fob and the 4 way flasher indicator on the dash should flash once.
10. Repeat if you have more key fobs. Only 5 can be programmed.
11. To exit, simply turn of the igniton and remove the ignition key.
12. Unlock the doors using the Lock/Unlock switch on the door and exit the vehicle.
13. Make sure the window is down when testing remotes in case you leave the keys inside.
14. Close all doors and test all remotes that were programmed.

Do not skip any steps or the process will not work.

If the 4 way flasher indicator does not work when inserting the key, you will need to start the process from the begining. If it still does not work the receiver may be your problem.

If the 4 way flasher indicator does not flash when pressing any button on the key fob then the key fob is the problem (dead battery or defective remote)

Dec 18, 2009 | 2002 Nissan Xterra

1 Answer

My renault laguna 1999 rt remote key fob wont work?


IF YOU TYPE 1999 RENAULT LAGUNA REPROGRAMME KEY INTO A GOOGLE SEARCH, YOU WILL BE ABLE TO PRINTOFF INSTRUCTIONS TO REPROGRAMME THE KEY TO THE KEY READER.THE IGNITION NEEDS TO BE OFF TO DO THIS

Jul 09, 2009 | 2004 Renault 181

4 Answers

Program a remote key for 03 A6


I have an A4 and did this to re-program my key:

1. used the key to start the car...then turned it off
2. put the key in the driver door (door closed)
3. pressed the lock button on the key fob once
4. turned the key to lock the door.

This is basically the steps in the owners manual, but the car must be started with the key first, and the key must be in the door lock before pressing the lock button.

Dec 10, 2008 | 2003 Audi A6

Not finding what you are looking for?
2007 Peugeot 207 CC Logo

Related Topics:

7,419 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

mike hayward

Level 2 Expert

279 Answers

lloyd cole

Level 2 Expert

250 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...