Drivers Side Rear Window Electric Motor Removal

The electric window could either be the fuse,switch, or window regulator motor at fault..Sometimes the window motor electric plug can vibrate loose or become loose from door slamming..Also the switch can become loose as well or contamination if you are lucky..You will have to remove door panel to inspect these components..and fuse panel..The light could be a faulty bulb..Check and replace bulb..before involving the signal indicator switch lever...If bulb is at fault go ahead and change bulbs at both rear sides..Do not try to repair signal switch because of air bag..If you can hold down on the turn signal switch and it works the switch is at fault...

its your soilnoid for window motor

You have to remove the inner door panel to
access the window regulator

You remove the regulator & then the motor from it

You Tube Video will provide a visual of several
similar window motor replacement jobs

Go there-- enter your car,question ,details,etc--- then move
around the site to watch various things

You're probably gonna need some regulators. Or you can give direct power to motor to see if it works, if it does...then its your switch.

Suppose it could be the motor itself in the front door

Removal & Installation
Motor - Front Door

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove the window control switch
3. Remove the front door trim panel and watershield.
4. Tape the window in the full UP position.
5. Disconnect the window motor electrical connector.
   NOTE Support the window motor while removing the window motor retaining screws.
   
6. Remove the window motor bolts and remove the motor.
7. To install, reverse the removal procedure.

Rear Door

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove the window control switch.
3. Remove the rear door trim panel and the rear door trim watershield.
4. Remove the door speakers.
5. Tape the window glass in the full UP position.
6. Disconnect the window regulator electric drive.
7. Position the connector for the window regulator electric drive inside of the door.
8. Remove the bolts.
9. Separate the window regulator electric drive from the rear door window regulator.
10. Remove the window regulator electric drive from the door.
11. To install, reverse the removal procedure.

Motor & Regulator



Fig. Front Door Trim Panel




Fig. Rear Door Trim Panel-Crew Cab


Regulator - Power Windows



Fig. Window regulator arm nuts




Fig. Window regulator bolts

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove the window control switch.
3. Remove the door trim panel.
4. Remove the door speaker.
5. Remove the door watershield.
   NOTE Do not remove the window glass from the door.
   
6. Remove the window glass from the window regulator.
7. Tape the window glass in the full UP position.
8. Disconnect the window motor electrical connector (power windows only).
9. Loosen the window regulator arm nuts and pull the arm from the mounting position.
10. Loosen the bolts and remove the window regulator.
11. To install, reverse the removal procedure.

Hope helped with this. Good luck.

if you don't hear the motor it's probably got a short or bad switch. If the motor runs and the window doesn't move you have a damaged gear.

1. Raise and support the rear door window glass to the full up position.
2. Remove the interior door handle.
3. Remove the rear door speaker.
4. Remove the water shield.
5. Disconnect the rear door window regulator motor electrical connector.
6. Remove the rear door window regulator rivets.
7. Remove the rear door window regulator by sliding the regulator arms off of the window glass track.
8. Installation is the reverse of the removal procedure, noting the following:
   • Cycle the door glass to make sure of engagement of the drive mechanism.
   • Remove the rear door window glass-to-regulator bolt or rivet.
   • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet.
   • Secure the rear door window glass in the full UP position with tape.
   • Disconnect the window regulator motor electrical connector.
   • Remove the 2 window regulator nuts.
   • Remove the 3 window regulator motor bracket nuts.
   • Install the window regulator assembly. Tighten the 3 motor bracket nuts to 89 inch lbs. (10 Nm).
   • Install the 2 window regulator nuts. Tighten the nuts to 89 inch lbs. (10 Nm).
   • Connect the window regulator motor electrical connector.
   • Remove the tape securing the rear door window glass in the full UP position.
   • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet. Tighten the bolt to 62 inch lbs. (7 Nm), or install a new rivet.
   • Install the window regulator motor
   • Remove the window regulator assembly.

Remove the window regulator motor

They should be the Same Motors.

You need to replace the window regulator assembly.
The cables that run the glass up and down have broken inside the regulator.

Hope this helps. A FixYa rating would be greatly apprecited.