The power door locks for my 1996 Odyssey just stopped working. I can't lock/unlock the doors with either the key fob or the front door lock buttons. When you try the door lock buttons, you can hear a buz noise in the front drivers door area. Even checked the fuse under the hood, noise stopped with no fuse. I think it is the door lock control unit but not sure. Any suggestions and any ideas how much to fix? Thanks Jim

Security Reset

How to reset my anti theft on my car (Lincoln LS) - CarGurus.ca

https://www.cargurus.ca > Discussion-t7468_ds782699
Remove your key from the ignition to end the resetting process. 122 people think this is helpful. ... How to remove anti theft from a 1997 Lincoln town car.
14 answers · 122 votes: Enter your car with your ignition key and your remote switch and insert your key into the ignition. ...

Programming instructions for 1995, 1996, and 1997 Lincoln ...

https://www.youtube.com > watch

1:21 How to program your 1995, 1996, and 1997 Lincoln Town Car remote keyless entry fob alarm by yourself at ...
YouTube · NO4DS4ME · Jun 9, 2016

Power windows. check fuses and relays

https://www.google.com/search?q=1996+lincoln+continental+windows+not+working

..

1. Get in your vehicle.
2. Close the door.
3. Put key in ignition
4. Do not turn on the ignition yet.
5. Hold down on the unlock button on the door panel. Do not let up.
6. Turn the key to ON, OFF, ON, OFF (while still holding the unlock button on the door panel).
7. Release the unlock button.
8. The door locks should cycle, indicating that you did everything correctly.
9. Have all your remote entry fobs available. Hold down on both the lock and unlock buttons until the door locks cycle. Do the same on all key fobs. This will re-program all of them.
10. Turn ON the ignition key to exit the program mode.
11. DONE.

dead battery in the key fob/ button battery

if the key does not turn the lock spray it out with wd 40 run key in and out of lock few times.because everyone uses remotes to open their cars the waffers in the door locks get coroded and wont fall in proper place when key is inserted.give it good cleaning and see if it will unlock

did some quick research for you and found this easy and very clear step by step instructions on how to program your transponder car key to your vehicle.. this works for the following models though :

Accord 2003 to 2006

Civic 1999 to 2006

Element 2003 to 2006

Odyssey 1999 to 2006

Prelude1999 to 2001

Accord SE 1997

CR-V 1998 to 2006

Insight 2000 to 2006

Pilot 2002 to 2006

now here are the steps:

1. Turn the ignition on
2. Press Lock/Unlock within 4 seconds
3. Turn ignition off and hen back on within 8 seconds
4. Repeat steps 2-3 two times
5. Press Lock/Unlock again within 4 seconds. The system should now lock and unlock the vehicle to indicate it is in programming mode.
6. In the next 10 seconds: press Lock/Unlock button allowing the doors to lock/unlock once; then press lock/unlock button of each remaining key, allowing the doors to lock/unlock once.
7. Switch ignition off and then remove the key

Civic 1996-1998

1. Turn ignition on
2. Press and hold the valet button which is situated on the radio within 5 seconds.
3. System should now lock and unlock the vehicle indicating it is in the programming mode
4. Within 5 seconds turn ignition OFF and press Lock/unlock on the remote fob to be programmed
5. Within the next 10 seconds, press Lock or Unlock of any remaining keys, allowing the doors o lock or unlock once.
6. Release valet key
7. Switch ignition off and then remove the key

Radio remotes 2 and 3 button types

1. Switch ignition on and repeat for 3 times.
2. Press he lock button, switch the ignition off and back on and then press lock button again.
3. System should now lock or unlock
4. Press the lock button of all remotes to be coded. The car should acknowledge this by locking/unlocking each time
5. Switch ignition off to exit the programming mode.

If you will have any further doubts or question to ask i suggest you to check out the page where i found this which is http://www.carkeyadvice.com/step-by-step-fob-programming-guides/honda :) i hope this was the solution you were looking for mate! happy happy new year!

You are going to need to check the power lock control moduel on the inside of the door panel. If the FOB appears to be working but the doors are not unlocking, you need to check this. I would also replace all fuses that control the locks. If both of these devices check out ok, you may need to replace your FOB. To check your power lock control moduel, manually lock and unlock your doors by pressing the lock button on the inside of the door. If it does not work, it is either the fuses or the power lock control moduel. If it works, your FOB has gone bad. Hope this helps! Please rate 4 thumbs up!

https://www.clublexus.com/forums/rx-1st-gen-1999-2003/395765-driver-door-won-t-lock-or-unlock-using-key-transmitter.html

Replace the key.
you should have a remote lock/unlock key fob, dose it not work?
Make sure that your battery and cables are in good shape, if batt is low or you have corroded cables there will not be able to activete all the way.
If this won't work then remove the door pannel an inspect the linkage, it may not be making full contact.

The driver's side door lock button is designed not to lock from the inside unless the handle is pulled, or the power switch is used. This serves as a reminder to not lock your keys inside.

If you are inside, and push down on the button (not the switch) hard enough to lock it, you've probably damaged it.

make sure than you have not split any fluids on the passenger front door most of the times is where the module to control the windows and doors is located, try by unpluging the batterie and the after a minute plug it back and see what happend but if any of your ft doors have been split with liquid or rain has gone inside then most likelly the module got moisture and not working