I have Aiwa TV MODEL No. TV-A149 Along with that channel it now shows a message in flashing red color that reads :- AGING 096dh Now when I press ''Display'' button on remote control volume goes off and this code is shown :- S123 K234 Y 000 001 1 vijay naresh

Possible the red gun is going bad In the CRT. Would need hooked up to a CRT tester to find out.

Its main system control memory IC is damaged. Replace it with same number. This IC is a very small one, having 8 solder terminals, and can be located very near to the main system control IC. Usually start with a number 24C**. Check and replace it. If you wish to get more details, surf this link. http://electronicshelponline.blogspot.com/ There are more than two thousand and four hundred posts. All are related to television and other domestic electronic equipment service help.

This problem has been answerd a few while ago.

Aiwa television comes with the option of blocking certain channels from viewing, allowing you to control which channels people using the television can view. However, if you forget the code that you entered to block the channels, you might find yourself unable to watch those channels. Fortunately, there are a couple of buttons on the television and the remote that you can press to reset the PIN and customer ID numbers, which unblocks the channels.

Turn the television on.

Press the "Volume Down" button on the front of the TV and press the "7" button on the remote at the same time.

Enter in a new PIN code and new customer ID.

Hello
Check your remote control hanset for proper functioning. Get into this link to know more about the faults and repair to remote contorls.
http://www.fixya.com/support/r10192276-cleaning_remote_control_handsets

If remote control functions proeerly, the front panesl switches to be suspected. If any one mong the microswitches inside got strucked, all functions will be distrubed. it will be best to follow any more after replacing these microswitches. These switches can be located just behind the control panel of the tv, soldered diretly to a printed circuit board. You have to replace all of the at the same time. Just undolder one amoung them as as sample, when you go to buy for a new one.
If this also does not help you, repalce its memory IC. This IC can be located very near to the main system control IC, will have 8 solder terminals. A very small IC and wont cost more. Eventhough it is very small, function of it when the set works is great. Replace it. When you buy this IC, make a keen look on it number. It is very important when replacing this IC. All these components stated above, can be bought from most of the electronic spare part selling shops st your town. OK.

my aiwa tv-- A219 is showing message AGING 2F01H in red color and nothing else except dispaly button is working.pls help me

have Aiwa TV MODEL No. TV-A209
The problem that I am suddenly facing is that I can't change channels or volume or use any other function. I can't even turn it off with remote control.

Its stuck randomly on a particular channel that I was watching at that point of time.

Along with that channel it now shows a message in flashing red color that reads :-
AGING
O6895H

Now when I press ''Display'' button on remote control volume goes off and this code is shown :-
S123 K234 Y
000 001 1


The numbers in the second line can be navigated by ''CH+'' button and changed between 0 and 1 by ''Vol+'' button.

I really don't know anything about this. So, please help me out of this problem.

Dear Sir, I have AIWA c142ske TV. No remote functions are working, even manual switches are also not functioning, It got stuck on One channel, The error which is coming on screen is

I have Aiwa TV MODEL No. TV-A149
The problem that I am suddenly facing is that I can't change channels or volume or use any other function. I can't even turn it off with remote control.

Its stuck randomly on a particular channel that I was watching at that point of time.

Along with that channel it now shows a message in flashing red color that reads :-
AGING
6EDEH

Now when I press ''Display'' button on remote control volume goes off and this code is shown :-
S123 K234 Y
100 000 0


The numbers in the second line can be navigated by ''CH+'' button and changed between 0 and 1 by ''Vol+'' button.

I really don't know anything about this. So, please help me out of this problem.

well reprogram your tv. i beleive there is an access infront of the tv. if not with your remote control.