Question about Samsung BN94-05038F Main Board for UN46D6050TFXZA BN97-06022A, BN41-01587E

1 Answer

TV won't turn on. Red standby light blinks

TV won't turn on. When plugged in, the red standby light next to the power button blinks twice 5 times in a row and then starts over doing the same thing. When power button is pushed nothing happens. The light just continues blinking in the same pattern.

Posted by Charles Fagnant on

Ad

1 Answer

eric allen

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 660 Answers

Samsung told me this was a common problem and I would have to have it serviced by an authorized repair facility.
My problem ended up being the internal power supply, but they also told me the main boards burn up.

Posted on Nov 06, 2013

  • 1 more comment 
  • Mosaub Al Masri
    Mosaub Al Masri Nov 07, 2013

    there is an IC need to be replaced it will cost you 1 dollar

  • abby
    abby Nov 23, 2013

    CAN YOU TELL US WHAT IS THE IC ?

  • kyle thomas
    kyle thomas Jan 07, 2019

    yes please what is the IC

×

Ad

5 Related Answers

Anonymous

SOURCE: Samsung remote control problem

Same issue as lisawrob
Check to see if there is another remote with something sitting on top of it. I had the same problem and found another remote transmitting (continously).

Posted on Aug 10, 2008

Ad

Anonymous

  • 39 Answers

SOURCE: samsung 50in tv trouble getting it started

the color wheel is bad. this whirring noise is caused from bad bearings in the 12v motor and possibly broken plastic panes from the wheel. DO NOT KEEP TURNING ON AS THIS CAN THROW PLASTIC PIECES INTO THE LIGHT ENGINE TUNNEL. very hard to retrieve debris from light engine. even small fragments can show up as large blemishes on the screen once the pix is magnified. needs professional service as light engine must be removed and realigned after replacement. mch

Posted on Mar 09, 2009

Anonymous

  • 1 Answer

SOURCE: bn59 00463 volume works nothing else cant turn on

Step 1: Remove the batteries

Step 2: Press the power button (red button) on the remote control 5 times.

Step 3: Replace the batteries and your remote should work fine.

Posted on Oct 27, 2009

Anonymous

  • 1 Answer

SOURCE: Samsung remote won't turn 630 LCD off. Only volume works.

yo moel
the way i did it was take the batteries out and hold powere button for 5 seconds put batteries back in and should be fine mate!

ahmed

Posted on May 17, 2010

Anonymous

  • 1 Answer

SOURCE: The TV button at the top keeps blinking and the

This light is caused when there is a fault with the circut board. If you are able to get the remote apart you might fid some liquid lik substance on the board. take a cotton bud and clean it dry put the batteries in it and it should work like new

Posted on Oct 10, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pn43d490 clicks blinks red light twice and will not turn on


do you have a dim screen? if you put a torch to the screen at an angle can you see the picture?if so this means the backlight is out, it could be the inverter board or the bulbs themselves though this is unlikely.do you get the 24Vgoing to the backlight from the psu?

Dec 09, 2013 | Samsung PN43D490 3D Plasma TV

1 Answer

Looking for a sky remote control code for beko.


Hello
The three digit Sky remote code for Beco TV are:

514 398 065

Four digit code is:

0125

1* Turn your TV and SkyHD box on and press tv on your remote control.

2* Hold down select and the red button together until the red light on your remote

control blinks twice (this is after about two seconds).

3* Press tv again.

4* Key in your TV's brand code. The light on your remote control blinks twice.

5* Press standby on your remote control.

If your TV switches off, press select.

The light on your remote control should blink twice.

If your TV does not switch off, press tv, then press standby.

Repeat the sequence of pressing tv then standby until the TV switches off,

then press select.

If the light blinks three times, your remote control has checked all the possible

settings for the code you used. Check you have the right code and start again

at step 1.

*6 Turn your TV back on and press the tv guide button on your remote control.

The TV Guide screen appears, meaning the remote control settings have
been reset.

Aug 12, 2011 | Televison & Video

1 Answer

What is the code for LG 37LE4500 TO WORK WITH SKY REMOTE CONTROL


I also have an LG TV. I used this 4 digit code: 0742.

TO PROGRAM THE remote USING THE 4 DIGIT CODE:

1. Turn your TV on.

2. Press tv on your Sky remote control.

3. Hold down select and the red button together for about two seconds, until the red light on the Sky remote control blinks twice.

4. Press tv on your Sky remote control again.

5. Key in the four digit code for your brand of TV. The light on the Sky remote control blinks twice. If the light blinks once only, recheck the code for your brand of TV and start again at Step 1.

6. Press the standby button on your Sky remote control. If your TV switches off, press select. The light on the Sky remote control blinks twice (code stored). If your TV does not switch off, press tv, then press the standby button. Repeat this (press tv, then standby) until your TV turns off, then press select (stores code).

Mar 12, 2011 | LG Televison & Video

1 Answer

I need code for sky remote control to operate sony kdl 32u3000 tv. Thank you


Here is the codes,533,038,039,064, Turn the TV on, hold down the SELECT and RED button at the same time,the light will blink twice, enter one of the three digit codes, the light will blink twice,if not, try another code,press STANDBY button, the TV should turn off, press SELECT, it will blink twice...hope this was helpful...

Apr 21, 2010 | Televison & Video

1 Answer

How do you tune Sky+ remote into Sony KDL46W5710 Television


The Sky+ remote should automatically default to Sony TV's. Leave the batteries out for a few minutes and try again. The Code for Sony is 0000.
Or try this :-

With TV and sky box on.
Press the 'TV' button on the remote.
Hold down the 'select' and the 'red' button (of the four coloured buttons) together, until the red light on the remote blinks twice. (takes 2 seconds)
Press the 'TV' button again.
Now enter four zeros, the red light on the remote should blink twice.
Press the 'standby' button (top right).
If the TV turns off, then press 'select' and the light should blink twice again, job done.

If the TV does not turn off then press 'TV' followed by 'standby' again.
Alternate pressing 'TV' 'Standby' until the TV turns off.
When it does, finish by pressing 'Select.
Check the red light on the remote, if it blinks 3 times, then it has run out of options for 0000.


Dec 19, 2009 | Televison & Video

2 Answers

Hitachi Ultravision won't turn on


it is the power board in the tv hase some bad capasators in it but can cost some money to fix if unsher how to do it on your own if you live in central new york i do have my own shop and im cheep but i can not warenty any thing but i can help 315-280-0508 storm electronics ask for corey

Aug 04, 2009 | Hitachi UltraVision 42HDS52 42 in....

1 Answer

How do i key in code for digibox


TO PROGRAM THE remote USING THE 3 DIGIT CODE:
1. Turn on the TV receiver
2. Press TV on the Sky Remote Control
3. Hold down SELECT and the RED buttons together for approximately two seconds, until the RED LED on the Sky remote blinks twice.
4. Enter three digit code from list for the receiver (early versions now flash twice).
5. Press select to enter code structure (the LED will flash twice if a valid code has been entered).
6. Now press the STDBY button and test other functions.
Repeat if necessary until a code is found that works most common functions.
TO PROGRAM THE remote USING THE 4 DIGIT CODE:
1. Turn your TV on.
2. Press tv on your Sky remote control.
3. Hold down select and the red button together for about two seconds, until the red light on the Sky remote control blinks twice.
4. Press tv on your Sky remote control again.
5. Key in the four digit code for your brand of TV. The light on the Sky remote control blinks twice. If the light blinks once only, recheck the code for your brand of TV and start again at Step 1.
6. Press the standby button on your Sky remote control. If your TV switches off, press select. The light on the Sky remote control blinks twice (code stored). If your TV does not switch off, press tv, then press the standby button. Repeat this (press tv, then standby) until your TV turns off, then press select (stores code).
If at this point the LED on the Sky remote control blinks three times then all possible codes for that make of receiver have been checked. Repeat from step one, ensuring that you enter the correct manufacturer code.
At the end of the sequence, if you see the TV Guide screen, the remote control setup process is complete. If you did not see the TV Guide screen, you must now complete the following steps.
8. Press tv on your Sky remote control.
9. Hold down select and the green button together for about two seconds, until the red light on the Sky remote control blinks twice.
10. Key in the number of the channel on your TV that you use for watching satellite TV.
11. Press select on your Sky remote control. The red light blinks twice. The remote control setup process is complete.
If after trying this, you still have problems, call your broadcaster's help desk. For your broadcaster's help desk number, select the Telephone Numbers option from the Services screen.

Dec 19, 2008 | Computers & Internet

1 Answer

TV REMOTE CONTROL NOT WORKING


1. Turn your TV on.

2. Press tv on your Sky remote control.

3. Hold down select and the red button together for about two seconds, until the red light on the Sky remote control blinks twice.

4. Press tv on your Sky remote control again.

5. Key in the four digit code for your brand of TV. The light on the Sky remote control blinks twice. If the light blinks once only, recheck the code for your brand of TV and start again at Step 1.

6. Press the standby button on your Sky remote control. If your TV switches off, press select. The light on the Sky remote control blinks twice (code stored). If your TV does not switch off, press tv, then press the standby button. Repeat this (press tv, then standby) until your TV turns off, then press select (stores code).

If at this point the LED on the Sky remote control blinks three times then all possible codes for that make of receiver have been checked. Repeat from step one, ensuring that you enter the correct manufacturer code.

At the end of the sequence, if you see the TV Guide screen, the remote control setup process is complete. If you did not see the TV Guide screen, you must now complete the following steps.

8. Press tv on your Sky remote control.

9. Hold down select and the green button together for about two seconds, until the red light on the Sky remote control blinks twice.

10. Key in the number of the channel on your TV that you use for watching satellite TV.

11. Press select on your Sky remote control. The red light blinks twice. The remote control setup process is complete.

Oct 17, 2008 | Philips HDD065 MP3 Player

1 Answer

Remote control set up code


Try searching for the code

To search for your television code:
1. Switch your television on (not in standby).
2. Press and hold down MAGIC until the ONE FOR ALL
1 red light blinks twice (the red light will blink once
then twice).
3. Press 9 9 1. The red light will blink twice.
4. Next, press POWER.
5. Aim the ONE FOR ALL 1 at your Television. Now press
CH+ over and over, until your Television turns off
(every time you press the CH+ key the ONE FOR ALL 1
will send out a POWER signal from the next code
contained in the memory). You may have to press
this key many times (up to 150 times) so please
be patient.
If you skip past a code, you can go to the previous
code(s) by pressing the CH- key. Remember to keep
pointing the ONE FOR ALL 1 at your Television while
pressing this key.
6. As soon as your television

Aug 21, 2008 | Televison & Video

Not finding what you are looking for?
Samsung BN94-05038F Main Board for UN46D6050TFXZA BN97-06022A, BN41-01587E Logo

459 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76455 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

 Grubhead
Grubhead

Level 3 Expert

5700 Answers

Are you a Samsung Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...