Leap pad problem loading

You should make sure that your iPad is running the latest firmware version. Also, make sure that your apps, especially the one you are having trouble with, is fully updated. These updates cover problems the software is having.

1. To check if your iPad firmware is up to date:
Go to "settings", then to "general" then to "software update".
2. To check on you apps update status, go to the "app store" icon,
then on the bottom, all the way to the right, there's an "updates" icon. The apps that have available updates are listed here. Make sure to update each out of date app.

Hope this fixes your problem!

Good Afternoon James,

I see that you are still having trouble with your Frigidaire Affinity washer, model# ATF7000E, finishing and now starting a load, even after replacing the door lock.

I would start by making sure that your washer door is completely closed.

Next I would check to make sure that your washer controls are not locked. You will see a "LOC" code if the controls are locked. To get them out of the lock mode, press and hold the "Options" and "Select" buttons at the same time for 10 seconds.

If you are still having trouble you will want to give your washer a hard reset. You can do this by either unplugging it or cutting the power at the circuit breaker for 2-3 minutes.

Once power is restored, if you are still having trouble with your appliance either not starting or not completing the cycle, I would recommend contacting either the manufacturer or your local authorized technician. Hope this helps.

-Best Regards-
WP

Its worth a try they might give you a deal because you have two

Cannot replace screen. Contact leap frog through the warranty. They have you deface the bad one and send a pic of it, then they mail you a brand new one

I have the same problem. I have contacted leapfrog support waiting for a response
Soo frustating. Il let you know if my problem gets resolved.

Hi johnsoncarli

I have had the problem before. It can be seversl things.
1. Bad motor brushes, or the brushes have created a lot of dust on the armatures and will strain the motors to work harder and lose power faster. Also, I don't know how old the chair is, however sometimes the older motors may need to be re-wires (copper wiring).
2. This is the easiest, with a programmer, program the fastest speed (100) and lower the torque. Torque is set high for hills. and lower for flat land. THe lower the torque the farther you can go on a charge.
3. I know you said you had your batteries tested, but 94% is not a accurate reading. They need to be load tested. You can go to an auto parts store to have them load tested. If under a load, even if they show 94% they may not have enough strength to carry the chair load. I have seen new batteries that wouldn't hold a good load. If while testing the load, the voltage drops 4 or more volts, replace the batteries, not just one, both. Even if the load test says they are good, replace them. Bet that will cure the problem.


Good Luck

mimiobility

Yes, i think the best solution would be to tech it but because it sounds like a technical problem.
Take it back and they will work on it.

I see this problem usually with haxed iphones, is yours haxed? Try plugging it into your computer, does your cpu recognize it and load itunes? even if it still shows the red battery. If you cant get itunes to recognize it then do a restore and this should fix the problem. If the above does not work you can try and press the power button for 5sec keep holding it and then plug it in to a power source, keep holding the button for another 5sec after and see what happens. If all else fails it may be time for a hard reset, if you dont know how, press and hold the menu button and the power button till you hear a beep, then let go of the power button and keep holding the menu button till you hear a second beep. Cali

I am having the same problem w/ our brand new front loader washer, it pauses constantly, and even when I can get the load to finish, I have to drain and spin atleast 3 x before I can even attempt to put in dryer, at this point it is taking me hours to do one load of laundry!!
Ugh-- Service man is coming tomorrow, so I will share what I learn...

Try taking it back to the store, or contacting leap frog for repair. Looks like in the US, the warranty is about 3 months, but in Canada or the UK it is longer.