Jacuzzi Signa 6 Whirlpool JAC-B540... - Page 5 - Answered Questions & Fixed issues

There is a very good chance there was a factory defect. Either the exit hole is misshaped or there may be a small sharp edge that could be eating up the flappers. I would contact the manufacturer telling them about your problem and see if they will replace the tank or just buy a bunch of flappers wholesale and change them when needed. good luck

Your problem is most likely NOT the air button but the switch in the motor. Air Switch Repair It sounds like you have a bad air switch located in your motor. The air switch is what the air hose connects to on the back of the motor or on the box on top of the motor. The other end of the air hose is connected to the air button on the lip of the tub. This is a latching air switch and when you push the air button it latches to send power to the motor. When the air button is pushed again it opens the latch in the air switch and stops power going to the motor shutting it off. Rod US Parts Center

The 'low-water' sensor installed in a bathtub is designed to NOT allow the pump to run without water contacting it. It sounds as if this is operating as it should. Once the pump comes on you should be able to touch the "logo" or the on/off button to turn the pump on and off. If the pump is not turning on/off when the tub is full of water you may be experiencing a problem with the control box under the tub skirt. Rod US Parts Center 888-521-6183

This issue will have nothing to do with the jacuzzi tub. You will find the problem exists in the way your home was plumbed by the plumber. Somewhere there is a clog in the water line going to the hot water faucet. Find that and you will solve your problem. Rod US Parts Center

If your hot tub water has all drained then you need to look for a leak obviously. Start in the cabinet area where there are unions attaching the pump and the electronics. Sometimes those will vibrate loose and will begin to leak. If all the unions are tight and you see no water then you need to start to look elsewhere around the tub for water leaks. It could be a broken manifold in the plumbing or a jet body. Rod US Parts Center

Here is a link to a site that sells jetted tub cleaners. Bath Parts Plus Bath Pump Spa Part Spa Accessories Powered by Network... Any of these cleaners work very well at removing the smell from a jetted tub and the bacteria in the pipes as well. Rod US Parts Center

What kind of switch are you referring to? Rod US Parts Center

The air button is located on the top lip of the bathtub or just below the top lip on the sidewall. It is held in place by a nut that is threaded up the length of the air button body. In order to change the air button you will need access to the underside of that air button so the nut can be unthreaded off the button body. Rod US Parts Center

The problem you are experiencing tells me that the air switch in the motor most likely the problem. This is a latching air switch that operates when the button on the side of the tub is pushed. The replacement TBS-339 air switch is around $21 Rod US Parts Center

Check the connections of the light bulb and any connecting wires. Short of this you may have a faulty transformer. Rod US Parts Center

What are you taking apart to clean? What is the nature of the cleaning you are trying to do? Rod US Parts Center

What is the nature of your question? Rod US Parts Center

What brand and model of skimmer do you have? Rod US Parts Center

FL is a "flow" issue. Check the filter to make sure it is clean. Start by removing it from the tub and see if that solves the error. The next item to check is the gate valves to make sure they are open all the way. There are usually one on either side of the pump and control box. Rod US Parts Center

This sounds to me like one or both of the sensors on your spa may be bad and need replacing. There are two sensors in each hot tub. One for the temperature of the water and a high limit to prevent the water from going over 112 degrees. If one of these is bad then the sensor will not read the correct water temperature. Rod US Parts Center

When you installed the new jet, did you install a new gasket on the wall fitting or use 100% RTF type silicone? In order to seal a wall fitting that is cracked an leaking, the replacement must have either the gasket or silicone to seal the wall fitting against the wall of the tub or it will leak when filled with water. Rod U S Parts Center

While the brand of the tub may be of importance to you it may not be important when finding parts for it. Bath tub manufacturers do not make anything that goes into their tubs i,e. the jets, pumps and controls are all purchased from various Mfg. Are you have any particular problems with either unit that would make you need the brand of either? Rod U S Parts Center

The hose under your tub attaches to the bottom of the air button and to the air switch located on the back of the pump or on the box on top of the pump. US Parts Center

Drain plugs on bathtubs are generic in size. Jacuzzi does not make them. They are made by other Mfg and installed by your local plumber when the tub is installed. US Parts Center

If your hot tub is running but NOT heating then you need to look at a couple of things.First, on the topside, is the heat indicator light on?If it is on and the tub is not heating then the temp sensor or the high limit sensor is not working and need to be replaced.US Parts Center